Question about 2003 Ford Ranger Regular Cab

1 Answer

2003 ford ranger 2.3 oil in intake

Runs bad

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

Check your pcv valve its probably stuck

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Ford truck xlt ranger2.3 litter oil in throttle body ? good or bad


I found out with my old 94 Ranger 2.3L that the oil breather does not have a filter element, which causes oil to "naturally" (as Ford puts it) accumulate in the throttle body and air intake hose. You can get an inline breather element at any parts store for a few bucks and install it on the breather line without harming anything, and this will stop. Cheers.

Jul 15, 2013 | 1996 Ford Ranger SuperCab

1 Answer

Ford truck xlt ranger oil in throttle body ? good or bad


The most common cause is too much pressure in the crankcase. It could be bad piston rings, or a problem with the PCV system. The engine is supposed to draw fumes from the crankcase into the intake and burn them, but the intake may be getting real oil instead of just fumes.

Jul 14, 2013 | 1996 Ford Ranger SuperCab

2 Answers

2003 Ford Ranger Edge V6. It is missing or hesitating on take off and in the early gears especially. Is it the fuel filter?


no ,they very rarely need changing unless the metal canister has corroded ,most likely its a mass air flow sensor in the air intake pipe

Jan 13, 2011 | 2008 Ford Edge

2 Answers

Check engine light came on and stays on but engine runs great


A lot of times yes it's just an emissions sensor acting up.

Mar 10, 2009 | 2003 Ford Ranger Regular Cab

3 Answers

Where is the pcv valve located on a 2003 ford ranger


  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Feb 27, 2009 | 2003 Ford Ranger Regular Cab

    1 Answer

    2003 ford ranger dtc code index


    hi there this code is a common problem with this engine
    the dtc code p2004 is related intake manifold runner control it is stuck open bank 1a .
    you need to replace controll switch

    Jun 17, 2008 | 2003 Ford Ranger Regular Cab

    Not finding what you are looking for?
    2003 Ford Ranger Regular Cab Logo

    Related Topics:

    143 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5501 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...