Question about 2002 Chevrolet Silverado 2500HD

1 Answer

How do you remove the pitman arm from a chevrolet

How do you remove the pitman arm from a 2002 chevrolet 2500hd?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

You have too have a pitman arm puller you can borrow one from auto zone!!!!
with a small deposit!!!

Posted on Apr 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a pitman arm on a 1984 chevy 4x4 blazer


It's an easy but physically demanding if you do not have a pneumatic set of tools. The specialty tools you will first have to get your hands on are a Tie Rod remover. otherwise know as a (pickle fork). There are two sizes of these large for ball joint removal and small for Tie rod removal. Looks like a big 2 pronged fork. The next Tool is a Pitman arm remover. Usually you can rent or barrow them from your local auto parts store. Drive your blazer up on to a set of repair ramps. Block the rear tires.The bolt to the center link from the pitman arm has a crown nut on it with a cotter pin going threw it. Remove the cotter pin.and remove the crown nut. Then with the Pickle fork and a 5 lb. sledge hammer. place the pickle fork between the center link and the pitman arm bolt. Give the end of the Pickle fork as many good blows on the other end as it takes for the center link to release from the pitman arm. Once that is done take a break I know you'll need it. Next is the Pitman arm to the steering gear shaft. Hope you can get your hands on a good breaker bar or an impact wrench and a socket large enough for the steering gear shaft nut. Remove the nut. Then place the Pitman arm removal tool between the pitman arm and the steering gear housing. Start tightening the threaded rod the remover up against the shaft. It is hard as hell to remove because pitman arms rarely go bad. It's usually the center link that fails.It will take a lot of strength to remove and you may want to use a little penetrating lube on it. Once you get that off you may want to replace the steering gear shaft seal as well. Otherwise just reverse the removal steps. The shaft is notched and so is the pitman are make sure they line up. then Torque to spec.s If you plan on keeping the blazer get a repair manual from your auto parts store. It will help you put a great deal.

Jul 24, 2012 | 1994 Chevrolet K1500

1 Answer

Can not get the pinion arm/balljoint separated from the power steering control valve


if you talking about removing pitman arm.you need a pitman arm tool J - 6632 or equivalent.the auto parts store should have one or snap on tools.

Apr 14, 2011 | 1981 Chevrolet Corvette

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

How to replace the gear box on a 1997 k1500 4x4 chevy suburban


remove the p/s lines to the gear box, take the nut of the pitman arm and seperate the center link of the pitman arm, remove the front shield, remove three bolts from the side of the frame holding the gear box onto the frame, you will need a puller to remove the pitman arm off the gearbox, reverse procedure to install. add fluid.

Aug 10, 2010 | 1997 Chevrolet Suburban

1 Answer

How to change the pittman arm and idler arm on a 1999 S10 Chevy Blazer 4x4?


Pitman arm requires a pitman arm puller, and a tie rod seperator or "pickle fork". Remove the cotter pin on from the joint on the pitman arm and center link, then remove the nuts from both ends of pitman arm. Use the pitman arm puller to remove the pitman arm from the steering gear, then use the tie rod seperator to remove the end from the center link. Reinstall and retighten nuts, do not leave out the cotter pin.
Idler arm will require tie rod seperator. Remove the cotter pin from the end at the center link, use the tie rod seperator to seperate the joint there. Unbolt the idler arm from the frame, and remove. On reinstalling remember to install a new cotter pin. It would be best to have the front end alignment checked after replacing these parts.

Apr 08, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

How to change pitman arm on a 1999 chevy suburban


you don't have to remove the steering box to do a pitman arm. Take off the one 1/4 in. nut, or whatever size it is, take the nut off the center link, put a pitman arm puller on the steering box side, and tighten the puller until you can't go any further, and hit the adjuster w/ a hammer hard, then tighten some more and repeat

Feb 02, 2010 | 1997 Chevrolet Suburban

1 Answer

I need to replace my idler arm and pitman arm on my 1997 chevy suburban 4x4 how do i do this


you will have to remove the steering gear box to change the pitman arm. the idler arm is on the other side by the passenger wheel. one nut and two bolts going threw fender take it off.

Dec 26, 2009 | 1997 Chevrolet Suburban

1 Answer

How to replace iddle arm and pitman arm on a 1986 g20 van


jack up and support van passenger side first with wheels straight remove wheel unbolt idler arm from center link and using a fork designed for removing front end parts some auto stores let u borrow / loan u fork remove idler arm unbolt (2) from frame replace and bolt in new one replace wheel other side wheels straight jack and remove wheel mark pitman at steer box so u can transfer mark to new pitman unbolt and us fork to remove pitman from center link us pulley to remove pitman transfer marks to new arm align up replace bolt up replace wheel done

Oct 30, 2009 | 1986 Chevrolet G20

1 Answer

I have a 1994 chevy k1500 4x4 and need to change pitman arm


Take the bolts out that attach the steering box to the frame and pivot the box so you can fit the puller on.
Leave the steering shaft and power steering hoses attached.
Mark the new pitman arm and old one in the same place and mark the pitman shaft to keep the same position of the new pit man arm on the old shaft as the old pitman arm.

Sep 06, 2009 | 1994 Chevrolet K1500

4 Answers

I need to replace the pitman arm,will I need to remove the steering gear box to get it off or is there an easier way. this is on a 1989 k1500 4 wheel drive chevey truck


yes you need to unbolt the steering box and drop it a little. not to hard. then you remove the nut and you will have to use a puller most of the time.

Jun 03, 2009 | 1989 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...