Question about 2002 Acura MDX

1 Answer

One of the sensors makes a clicking nosie when rev up it stops

Hi my 02 mdx makes a clicking nosies it is on top of the throttle body next to the map sensors .

i don't know what it is called. i had a code for a misfire for 4 cyclinders/ i changed all the plugs and i feel the car is normal know while i was checking it i heard this clicking noise which is wierd

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 23 Answers

The sensor that is clicking is normal that is the evap purge solenoid

Posted on May 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i have vw polo 2006 model it wont rev brake every thing is working but still on limp mode please help


sounds like the MAP sensor and TPS may not have been set/ adjusted correctly

Jan 06, 2015 | Cars & Trucks

1 Answer

Horn wont blow


check and see if they are plugged in check for bad fuse

Apr 05, 2014 | 2004 Pontiac Grand Prix

1 Answer

Screaming nosie coming from mini cooper automatic


Possible power steering pump failure

Jan 25, 2013 | Cars & Trucks

1 Answer

When i push on the gas it sound like it wants todie it bogs out but is still on n takes for eve to get to 30 but after 30 mph it speeds up fast and then stop at like 60 mph but has a high rpm kinda nosie n...


Hello; I have found that problem on a lot of Impalas.(1) It could be the (TPS) throttle positioning sensor located on the throttle body.(2) It could also be the fuel pressure valve located on the end of the fuel rail on the 3.4 liter.Or the combination of the two

Jun 16, 2011 | 2002 Chevrolet Impala

1 Answer

Location of tps and map sensor on a 02 jeep grand cherokee 4.7l


Both are attached to the throttle body. Tps is on the other end of the throttle plate shaft opposite the linkage, MAP is on the side...has small vacuum hose underneath and is flat, about 3" long. The other item on the TB is the idle air motor, next to tps.

May 07, 2010 | 2002 Jeep Grand Cherokee

2 Answers

Where would a map sensor be located? on 1999 gmc suburban


Hi, the manifold absolute pressure (M.A.P) sensor is located on the intake manifold. I am not familiar with the GMC vehicles as I am in South Africa. The M.A.P sensor is usually situated on the top of the intake manifold furthest from the air intake/ throttle body. I hope this info will help.

Nov 24, 2009 | 1999 GMC Suburban

2 Answers

High Idle 2


I would look at the codes,, jumper the two upper connector holes in the diagnostic link with a paperclip,, turn the key on, and read the blinks of the check engine light,, first will come 3 12 codes then any error codes. If you get a repair manual for that vehicle it will tell you how to perform these tests.

Mar 11, 2009 | 1985 Pontiac Firebird

1 Answer

Engine revs high


I've seen before where the IAC sensor gets dirty. The IAC sensor is located on the top of the throttle body. If you refer to the throttle body as a clock, and picture the egde closest to the front bumper is 6 o'clock then the IAC sensor would be located at 12 o'clock. I think in a 02 GC it should have vaccum lines attached to it, and it's held down by couple of phillp's head screws. (I think) Take it off and clean it with throttle body cleaner until all the black gunk is out of it.
If you are not sure where the throttle body is, find the air filter box under the hood located on the driver's side lower corner. There will be a plastic "tube" going from that box to the top of the engine. Take this tube off and any part that connects to the top of the engine. You will then see the throttle body. It would also be beneficial to clean the throttle body out as well. (It only take a minute and it can only help your gas miliage.) You can find throttle body cleaner at any auto parts store, or Walmart or Target. Let me know if this helps, thanks!

Dec 09, 2008 | 2002 Jeep Grand Cherokee

2 Answers

I have a 2003 Ford fusion 2 TDCI


Have your electrical wireing checked for shorting & grounding -to body metal-faults.In perticular the leads to the instrument cluster-look for wireing insulation cuts or cracks & have them taped or sleeved

Jul 10, 2008 | 2004 Ford Fusion

Not finding what you are looking for?
2002 Acura MDX Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...