Question about 2002 Chrysler Town & Country

1 Answer

Needle on the speedomer has goon all of the way around and is pegged up against the pin

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had this same thing occur in my 2001 Town & Country, it always happens when I have to do any electrical work that requires unhooking the battery. Once the van restarts, the needle swings around backwards, but there is a small retaining nub that keeps it from making a full revolution. In my 2001 this is easily fixed, you just pop off the dashplate around the upper half of the steering column, and then there are four bolts holding the clear plastic instrument panel cover in place. Once you remove those, you just pull off the speedometer needle, then replace it on the other side of the retaining nub. Be careful when touching the little nub however, it is rubbery and quite delicate. Hope this works for your 2002!

Posted on Apr 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grinding noise over 30 mph


you would have to find out where the speedomator wire/cable
connects
heres some idea

there is a gear at the end of a speedomator cable

try this 1st hit me back if this dosent work

Nov 01, 2012 | Mazda MX-5 Miata Cars & Trucks

1 Answer

My speedometer isn't working on Jeep Grand Cherokee, the hands aren't spinning and is beneath the rubber peg


Disconnect the posative terminal then touch the terminal to the posative a few times quickly it will reset your odometer needle to above the resting pin. This happens because you moved your posative terminal and the needles spun around and sat on the wrong side of the pin.

Oct 23, 2012 | 2000 Jeep Grand Cherokee

1 Answer

3.0 montero speedometer pegged out


look and see if the needle jumped passed the little pin on the face you might need to remove the lens and pop it back over the pin

Aug 10, 2012 | 2000 Mitsubishi Montero Sport

4 Answers

How do i get the needle to go back around to the top side of the peg on the fuel guage of my 1997 chevy malibu


Don't disassemble the dash! It will take hours and will rattle from now on. Use a very small gauage of wire, inserted in the odometer reset botton hole, to move the needle back around. It takes a minute or 2. This guage problem usually happpens when the battery is disconnected.

Jan 27, 2010 | 1997 Chevrolet Malibu

1 Answer

My gas hand has flipped around to bottom of fuel gauge and is hitting peg on bottom. How can i get it back around to correct position. The car died as the gauge was coming up to full and needle continued...


Fuel pump!perhaps not working!sit in car turn ignition on do not atempt start or crank engine you should hear a grunt sound from back seat area like a GRRRRR if not fuel pump not working!

Dec 28, 2009 | 2006 Nissan Maxima

1 Answer

1999 buick when fuel gauge drops below 3/4 it is is not accurate


i dont know the specifics of a Regal, but usually, when a needle fluctuates too much, is because the float gauge in the gas tank is worn out, or its mount became loose. You cant see that effect on a full tank because the instrument needle and the float are pegged against the stop.

Nov 23, 2009 | 1999 Buick Regal

1 Answer

I have an XJ6 1986 Jaguar, speedometer sometimes works


The gear is stripped either on the speedometer or at the tranny.

Apr 24, 2009 | 1986 Jaguar XJSC

1 Answer

Speed


The speedometer is driven by a signal from the Vehicle Speed Sensor (VSS). The VSS is mounted on the Power Steering Speed Sensoron the top of the back of the transmission (differential housing). There is an electrical connector and two small screws that hold the VSS to the PSSS. Be careful, there is a small link (key) that is between the VSS and PSSS which mechanically drives the VSS.

Feb 07, 2009 | 1992 Honda Accord

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...