Question about 2004 Toyota Corolla

1 Answer

I have a 2004 corolla having problem with headlight

The driverside low beam headlight burns up the connector that the headlight clips into. I have gone to the junkyard and replaced it 2 times now and it keeps burning the clip could this be a fuse problem? The other headlights are fine is just the one lowbeam on drivers side.

Posted by on

  • rstoops1 Apr 19, 2009

    Thank you for the help I will ask an electrician at work since I have no electrical exp.

  • Roberta Smith
    Roberta Smith May 11, 2010

    locate the relay in the engine compartment fuse box near the battery for that specific headlight function and replace it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

It's not a fuse problem, check the ground for that light assembly

Posted on Apr 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

1 Answer

Headlight low beam r side no power high beam works fine


Sounds like the low beam element in the right side is burned out. The auto parts store should be able to verify that and sell you a new bulb.

Aug 25, 2014 | 1998 Ford Explorer

1 Answer

I have no low beam headlights. The high beams work and I have changed the switch and bulbs and checked the fuses. what next


Check the connectors that go to the headlight bulbs to see if they are burned or melted. Low beam lights are on longer than high beams. The heat buildup around the connectors normally melts them.

Sep 27, 2010 | 2005 Chevrolet Trailblazer Ext

1 Answer

2004 elantra - front parking light replacement


The little parking light (also known as a city light) is in a plastic connector below the low beam lamp that simply slides out of the headlight assembly.

Grasp the plastic connector and pull back away from the headlight assembly and you will be able to unplug the light from the connector for replacement.

Jan 10, 2010 | 2004 Hyundai Elantra

1 Answer

How do you replace the drivers side headlight bulb on a 2004 New Beetle convertible?


1. Remove headlight housing. A.Open Hood and pull the release lever at the back of the housing. The headlight housing slides in and out of the body in tracks. B.Pull out the headlight housing far enough to disconnect the electric connectors, then slide the housing completely out. 2. Remove the retaining clip to remove the upper (low beam) or lower (high beam) bulb from the holder from the back of the housing unit. Remove the old bulb(s). 3. Do not touch the bulb with your bare hands! Wear clean gloves or hold with a clean paper towel. Fingerprints on the bulb will cause the bulb to burn out or explode!. Insert the new bulb. 4. Replace the retaining clips and insert the housing back into the tracks and into the body. Plug the electric connectors in and insert the housing completely. 5. Reposition the release lever to the original position being careful not to break the plasic lever. 6. Check your lights for operation.

Nov 01, 2009 | 2004 Volkswagen Passat

1 Answer

Low beams not working on 2004 Toyota Tacoma


check your multi function switch (headlamp / dimmer / signal) check for power on outlet side of connector to both hi and low beams. sidebar- I have seen both low beam elements burn out together, but if you have replaced both bulbs not the issue, if not give it a shot, stranger things have happened.

Aug 25, 2009 | 2000 Toyota Corolla

1 Answer

2004 Chevrolet Trailblazer


First face the vehicle so the battery in on the right.
Second open hood.
Third Remove the Grill by pushing firmly on two retainer clips that are on the top, use the wide slot screwdriver to get the rest of the clips off. Pull up gently on the grill it should then pop out. The grill extends under each headlight assemblymag-glass_10x10.gif any other retainer clips should release when the grill in popped out.
  • Step 2 Fourth on top of the headlight assembly you will see one 1" tab on the right and left side, pull the tabs upward about two inches and this should release the headlight assembly. You then should be able to pull the headlight assembly out toward you.
  • Step 3 Finally at the back of the headlight assembly you will see two rubber caps one for low beam and one for high beam, the white base is for the low beam and the black base is for the high beam. Unsnap the wire harness from the bulb base, turn the bulb clockwise.

    Replace the bulbs high beam on the outside and low beam on the inside.
  • Jun 19, 2009 | 2004 Chevrolet TrailBlazer

    1 Answer

    How to replace low beam bulb on 2004 baja


    I was able to locate an owners manual for the vehicle. The large plastic weatherguard protecting the headlight bulb connections needs to be rotated CCW about 90 degrees, and removed to provide access to the bulbs. Then remove the center connection for the low beam and release the spring clip retainer to release the low beam bulb. Replace with new bulb and reconnect/reinstall retainer clip, center connector wire, and weatherguard. Note that this is the procedure for the Turbo Baja...non-Turbo model is different.

    Jan 02, 2009 | 2004 Subaru Baja

    1 Answer

    How do you replace the driverside low/high beam?


    remove the front bumper if you mean the whole unit if you mean the bulb its just as easy to remove the headlight

    Oct 17, 2008 | 2004 Volkswagen R32

    Not finding what you are looking for?
    2004 Toyota Corolla Logo

    494 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8140 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...