Question about 2005 Pontiac Grand Am

1 Answer

Got my stereo stolen out of my 2005 Grand Am, and now neither my turn signals or my hazard lights work. I looked for torn or pulled out wires, but the only four that were loose were all attached to a unit beneath the console that claimed it was for the door chime... The fuses seem fine, and I am kinda lost as to why the signals aren't working.

Posted by on

  • silentthunde Apr 20, 2009

    No, I wish... they simply aren't working. I had thought the same thing... but turned them on, walked around te car.. and no lights.

  • silentthunde Apr 21, 2009

    by test light, do you mean a multitester? I have one of the probe style, yes... includes resistance, capacitance, voltmeter, etc... if you mean something else, like a trouble code reader or a timing light, then, no... dont have one.


    As for the button, yes, the turn signal switch and the hazard switch both seem to actuate.. just the lights dont work. Again, they worked literally the day before the stereo was ripped off... so I am currently assuming that it had something to do with that... the ceter of the center console was hanging, but the only wires I found loose, so far, were for the dinger.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 1,000 Answers

The only thing that should not be working would be the audible turn signal / hazard signal sound. When the turn signals are activated, the audio (radio) system generates a clicking sound that indicates the signals are working.
When the radio is missing, no sound is generated.
Are your turn signals working outside, but no sound or are the signals not working at all.
Let me know.
Regards,

Posted on Apr 19, 2009

  • Bruce Bracey
    Bruce Bracey Apr 20, 2009

    The next thing to check is the hazard flasher switch. Is it connected and does button work properly. Let me know if you have a test light and we can contiue.

    Regards,

  • Bruce Bracey
    Bruce Bracey Apr 21, 2009

    The "dinger" or chime module is located under the dash. Were is your hazard switch located, on the dash or in the steering column.

    It should be in and above your radio opening. The wire colors to the switch are black, orange, pink, purple, dk blue, lt blue, and gray. Make sure you have voltage on the orange and pink wire with the key in the run position. Make sure you are showing continuity to ground on the black wire with the key in the off/lock position.

    Let me know what you find.

    Regards,

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Pontiac Grand Prix front left turn signal went out, I replaced the bulb and the light comes on but the turn signal still doesn't work. If I have the lights sent on automatic the right parking


Hey I literally just today had the same problem, put a new bulb in the light was on but did not blink!!!! SUPER EASY SOLUTION, you simply have the bulb in too far. I gently pulled mine out a tiny bit and it started working fine... guarantee that's all that's happening to you!!!

Jan 25, 2013 | 2005 Pontiac Grand Prix

1 Answer

I'm trying to install my arrow signal lights for my 2005 jeep grand cherokee. where are my hazard wire located???


its located going down the steering column, it runs from the turn signal switch down the column,and to the flasher then to lights.use a test light to locate the right wires.

Mar 01, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Brake light/turn sigs dont work.But lights are on?


Ok, GM had a problem with their hazard light switches in the years of around 2001-2005. These caused some bizarre workings concerning the hazards, lights, turn signals, etc. The circuits overlap, and when the switch malfunctions, it makes for some odd happenings. Normally, when the hazards are on, they cancel out the brake lights and the turn signals, since they use the same circuits. The normal taillights use a different filament in the same bulb, which is why they light up brighter when you press the brakes. The aftermarket has come up with replacement switches in response to these inherent problems, so do not get your switch from GM. Places like RockAuto.com will sell these, though not necessarily this place, it's just the one I use. Usually, GM put these in the steering column, so replacement can be tricky for the average person, as it involves taking apart some of the steering column.

Feb 22, 2010 | 2004 Pontiac Grand Prix

1 Answer

Problem with my 97 Chevrolet S10 Blazer


I'd look into the multifunction switch. That controles both hazard and turn.

Dec 12, 2009 | 1997 Chevrolet Blazer

2 Answers

Turn signals, hazards not working


Mine just went out this past week and found the flasher/hazard fuse inside the glove compartment under the plate with the pull cord to access.The 1994 Jeep Grand Cherokee Laredo AWD part# on the fuse and called to confirm with a Jeep dealer is:
56007243 and appx. 44.00 from the dealer, may be able to get from an auto store as well.

Good luck if it is the fuse box you were looking for.

Aug 09, 2009 | 1994 Jeep Grand Cherokee

1 Answer

No taillights, have brake lights


have u check that the wires wert pulled off when they pulled radio out look on top of brake pedal see if the wires r on switch

Jun 07, 2009 | 1995 Saturn Sl

1 Answer

Hazard light modulator


you will have to replace the turn signal and windshield wiper assembly.Its very easy to do just remove the plastic cover over the steering wheel and remove the 2 screws that hold it in place.I found this item online for $35.00

Jun 23, 2008 | 2005 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...