Question about Buick Century

1 Answer

Exploded view i would like an exploded view of 3.1 water pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Go to a local gm dealer parts department. Check your local library for a chilton auto manual.

Posted on Apr 19, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 523 Answers

SOURCE: I need an exploded view of water pump replacement

Not too difficult of fix. You'll need to remove the serpintine belt. Drain the radiator. Remove the pulley from the water pump ( I believe three 10MM bolts) After removing this pulley you'll have access to all of the bolts holding in the water pump (I believe there are 5 or 6 8MM bolts) Reverse on install. No need to over tighten on the replacement pump as it has an o-ring seal. Take special care in reinstalling the serpintine belt. I'd get a bit of help to help hold the belt in place as you go.

I hope this may have assisted you, please let me know.

Thanks,
Tom

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

1 Answer

Where is the water pump on a 2004 monte carlo


Several engine sizes there; check this diagrams (click images for zoom)...


zjlimited_2007.jpg

Fig. Water pump assembly mounting-3.1L and 3.4L engines


zjlimited_2008.jpg

Fig. Water pump mounting-3.5L engine


zjlimited_2009.jpg

Fig. Exploded view of the water pump assembly mounting-3.8L engine

Hope helps (remember to rating this free answer and leave some testimonial comments here).

Oct 09, 2011 | 2004 Chevrolet Monte Carlo

1 Answer

Where is the fuel pump on a 1965 ford mustang 289


Exterior tank side...

zjlimited_687.gif

Fig. 1: Exploded view of the mechanical fuel pump on most V8 engines

zjlimited_1796.jpg

Fig. Exploded view of the pump mounting (click image for zoom)

Hope helps.


Sep 06, 2011 | Ford Mustang Cars & Trucks

2 Answers

Replace water pump 1995 aurora


Water Pump REMOVAL & INSTALLATION 3.5L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Partially drain the cooling system.
  3. Remove or disconnect the following:
    • Water pump pulley bolts, loosen but do not remove at this time
    • Drive belt
    • Idler pulley
    • Water pump pulley
    NOTE: The water pump is attached to the engine with both long and short bolts, be sure to note their locations.
    • Water pump and discard the gasket
    NOTE: Note the locations of the 5 long bolts.
  4. Clean the water pump mounting surface. Fig. 1: Be sure to install the 5 long water pump bolts in the correct locations - 3.5L engine 9300z502.gif
    Fig. 2: Water pump mounting - 3.5L engine 9300z503.gif
    To install: NOTE: Be sure to install the 5 long bolts in the proper locations.
  5. Install or connect the following:
    • Water pump using a new gasket. Torque the bolts to 124 inch lbs. (14 Nm).
    • Water pump pulley
    • Idler pulley. Torque the bolt to 37 ft. lbs. (50 Nm).
    • Drive belt
  6. Refill the cooling system.
  7. Start the engine and check for leaks.
3.8L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Serpentine belt
    • Heater and bypass hoses from the water pump
    • Water pump pulley
    NOTE: The long bolt can be removed by aligning the bolt head with the frame rail hole.
  5. Install an engine support fixture.
  6. Remove or disconnect the following:
    • Torque axis mount
    • Water pump and discard the gasket
    To install: Fig. 3: Exploded view of the water pump and mounting bolt locations - 3.8L engines 7922xg01.gif

  7. Thoroughly clean all the sealing surfaces.
  8. Apply a thin bead of sealer around the outside edge of the water pump
  9. Install or connect the following:
    • New gasket
    • Water pump. Torque the inlet and outlet side bolts to 29 ft. lbs. (39 Nm) and the remaining bolts to 97 inch lbs. (11 Nm).
    • Torque axis mount
  10. Remove the support fixture.
  11. Install or connect the following:
    • Water pump pulley
    • Water pump hoses
    • Serpentine belt
    • Water pump pulley bolts. Torque the bolts to 115 inch lbs. (13 Nm).
    • Negative battery cable
  12. Refill the cooling system.
  13. Start the vehicle and check for proper operation.
4.0L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Air inlet duct
    • Water pump drive belt cover
    • Water pump drive belt
    • Lower radiator hose and bypass hose
    • Thermostat housing from the water pump housing
    • Water pump from the water pump housing, by turning the locking ring with a Water Pump Remover/Installer tool J-38816
    To install: Fig. 4: Exploded view of the water pump housing and water pump - 4.0L engine 7922xg02.gif

  5. Install or connect the following:
    • Water pump, seat the locking ring
    • Thermostat housing to the water pump housing
    • Lower radiator hose and coolant bypass hose
    • Drive belt and drive belt cover
    • Air inlet duct
    • Negative battery cable
  6. Refill and bleed the cooling system.
prev.gif next.gif

Jan 24, 2011 | 1995 Oldsmobile Aurora

1 Answer

Where is the water pump


Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif
  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Jul 13, 2010 | 1997 Toyota RAV4

2 Answers

How to change water pump on toyota sienna


3.0L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Wiper and blade assembly Top cowl seal and panel Window washer hoses, from the ventilator louvers Left and right ventilator louvers Heater air duct Timing belt
  5. Mark the left and right camshaft pulleys with a touch of paint.
  6. Remove or disconnect the following:
    NOTE Be sure not to mix up the pulleys.
    Right and left camshaft pulleys bolts Pulleys from the engine
    No. 2 idler pulley by removing the bolt 3 clamps and engine wire from the rear timing belt cover 6 No. 3 timing belt cover-to-engine bolts Water pump nuts/bolts Water pump and gasket from the engine

    9c53b11.jpg
    Fig. Exploded view of the components to gain access to the water pump-3.0L engine


    cf2cc65.jpg
    Fig. Exploded view of the water pump and related components-3.0L engine

To install:
  1. Check that the water pump turns smoothly. Also check the air hole for coolant leakage.
  2. Apply liquid sealer to the gasket, water pump and engine block.
  3. Install or connect the following:
    NOTE After tightening the bolt, be sure the idler pulley moves smoothly.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    Water pump, using a new gasket. Tighten the nuts/bolts to 53 inch lbs. (6 Nm). Rear timing belt cover. Tighten the 6 bolts to 74 inch lbs. (9 Nm). Engine wire with the 3 clamps to the rear timing belt cover No. 2 idler pulley. Tighten the bolt to 32 ft. lbs. (43 Nm).
    Right-hand camshaft pulley, with the flange side outward.
    Tighten the camshaft bolt to 65 ft. lbs. (88 Nm), using the removal tools Left-hand camshaft pulley, with the flange side inward.
    Tighten the camshaft bolt to 94 ft. lbs. (125 Nm), using the removal tools Timing belt
  4. Fill the engine coolant.
  5. Install or connect the following:
    Heater air duct Left and right ventilator louvers Window washer hoses to the ventilator louvers Top cowl seal and panel Wiper and blade assembly Negative battery cable
  6. Start the engine.
  7. Top off the engine coolant and check for leaks.

Hope this help.

Mar 23, 2010 | 2004 Toyota Sienna

1 Answer

How do I replace the thermostat in a 2001 Nissan Sentra


WARNING Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure coolant escaping from the radiator.
To remove and install thermostat, refer to illustration and water pump procedure.


612dcdc.gif

Fig. Exploded view of water pump and thermostat components-1.6L engine

f6e0bbc.gif

Fig. Exploded view of thermostat and components-1.8L engine


2b67e32.gif

Fig. Exploded view of thermostat and components-2.0L engine


Removal & Install
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the lower radiator hose.
  5. Remove the water inlet and take out the thermostat.
  6. To install perform the following:
    Install gum ring to thermostat Install thermostat with jiggle valve or air bleeder at upper side
  7. To complete installation, reverse remaining removal procedure.
  8. Fill the cooling system.
  9. After installation, run engine for a few minutes and check for leaks.

Hope helped with this (remember rated this) Good luck.

Nov 05, 2009 | 2001 Nissan Sentra

1 Answer

Water pump is leaking


have you tried http://www.international-auto.com/ yet? They specialize in FIAT parts. Maybe they can help you.

Mar 20, 2009 | Fiat X1/9 Cars & Trucks

1 Answer

Water pump


1. Drain the coolant and disconnect the coolant outlet pipe connection hose from the coolant pump. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt idler. 4. Remove the coolant pump mounting bolts, then remove the generator brace. 5. Remove the coolant pump assembly from the cylinder block. See an exploded view:
d0ab616.gif

Jun 27, 2008 | 1997 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

551 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...