Question about Jeep Grand Cherokee

1 Answer

How do I remove front u joint from car? thank you

How do i remove front u joint from 97 grand cherokee? thank you

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Take out drive shaft take out retaner clips take hammer and hit the u-joint not the part in the drive shaft and it should come out .Then when u put it back in thecaps should slide back in when get it most the way back in get a socket and a hammer and hit it intill u can see the place where the clip gos back in hit it soft so you don't knock the needles out

Posted on May 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 grand cherokee-6cyl When making tight turns,


Hi, the likely problem is a worn out CV joint on one of your axles. Check for a torn boot on either axle. Once a toot tears open, dirt gets in and wears out the joint. Please let me know if you have more questions, and thanks for using FixYa.

Aug 03, 2011 | 1996 Jeep Grand Cherokee

2 Answers

WHERE THE OXYGEN SENSOR LOCATION ON 1999 JEEP GRAND CHEROKEE


just below the exhaust manifold on the drivers side of the jeep.... u will need to go underneath the jeep an may even have to remove the water shield that is under the front of the jeep..

Jul 16, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How do you remove the front drive shaft in a 1995 jeep grand cherokee limited


Use white paint, chalk or a scribe to mark the relationship of the front U joint to the front diferential pinion yoke. Mark the relationship of the rear U joint flange to the transfer case companion flange. Unbolt the front end of the drive shaft from the pinion yoke and the rear end from the transfer case companion flange and remove the drive shaft from the vehicle.
hope thei info helps.
sammyc47

Feb 24, 2011 | 1995 Jeep Grand Cherokee

1 Answer

Loud grinding noise (a bit like a football rattle) at the front of a 97 Jeep Grand Cherokee, dependant on road speed not engine revs, It virtually disappears in reverse. Any idea's? Thanks Pete


Hi, Going throught this one myself, I have had front diff open = OK, transfer case = OK, Auto = Ok. found out that a few have had problems with front bushes ( rubber joints) which I replaced recently, they are harder than the gen part and will vibrate causing a "drone" sound at certain speeds, particularly 40-60 kmh and 100kmh (iam in Australia).
If you have replace your bushes or thery may have become hard????
Cheers
Marti (oz)

Jan 09, 2011 | 1997 Jeep Grand Cherokee

1 Answer

97 jeep. Removing front wheel bearing


Most times you can squirt some wd40 on the ends of the axle spline, then put the axle nut on backwards so the castellated side is towards the bearing hub and run it onto the threads till the axle and nut are flush. (So you don't damage the threads or mushroom the end of the axle.) Once you have done that you can give it a really hard shot with a decent sledge hammer (two lb or heavier) striking it as squarely as possible. I have never had one refuse to come apart when I do this!!!

Feb 08, 2010 | 1997 Jeep Grand Cherokee

2 Answers

My 97 jeep grand cherokee makes a chirping sound under front


The noise and the light may or may not be related. The noise may be the wear indicator on the brake pads touching the rotor (they are supposed to do that when brakes are worn) The abs light triggers off a wheel on the axle end. If you have a bad joint on the axle, it could be noisy and causing the wheel to not have the proper clearance to the abs sensor. You really need to take the wheel and brake assembly off and carefully inspect everything. Make sure all abs sensor wires are undamaged...it doesn't have to be at the same wheel that's chirping.

Sep 26, 2009 | 1997 Jeep Grand Cherokee

1 Answer

97 jeep grand cherokee limited shakes at high speed


-Tires need to be rebalanced, tire weight missing
-excessive tire wear from not rotating tire.
-Play in tie rods.
-CV joints are worn.
-wear in upper or lower ball joints.
-excessive wear in u-joint.

Aug 16, 2009 | 1997 Jeep Grand Cherokee

2 Answers

I cant find a cv type front drive shaft for my 97 jeep grand ch.


Yes u can drive with it out its not going to hurt anything do your self a favor like i did on mine go the junk yard get a yolk off a dana 30 the xj will work also and 93 to 95 grand cherokees use the same yolk and drive line make sure u get the u joint style drive line and yolk its only like 30 to 40 dollars for these parts versus 150 to 280 to have the crappy cv style driveshaft rebuilt it way stronger

Mar 01, 2009 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...