Question about Daewoo Nubira

1 Answer

My jeep TJ will start but then it shuts down after approx. 2 seconds of running. No matter how much gas I give it it will not continue to run. It will start again and again but always shuts down.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 126 Answers

Possible fuel filter,it will allow just enough for start but not enough to run.Not a 100% possitive answer but is best place to start.

Posted on Apr 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the gas shut off reset jeep wrangler tj


Jeep does not have an inertia switch. It is computer controlled with relays

Mar 09, 2015 | Jeep Cars & Trucks

1 Answer

99 Wrangler TJ Sport 4.0L Straight 6 Shuts off while driving


the pcm is suspect in that year jeeps. simple easy test. locate pcm usually on firewall passenger side under hood. 3 large cables going into it on most. start jeep. let it idle. wiggle one wire at a time. does it shut off?? bad pcm solder joints inside are broken. doesnt shut off?? another issue to be determined.

Jul 17, 2017 | 1999 Jeep Wrangler

1 Answer

My 1997 Jeep Grand Cherokee Laredo is starting to have a ''slight'' hesitation after I shut it off and re-start it again. WHen I accelerate at first it hesitates a bit. I let off the gas for a few seconds...


A slight hesitation after engine shut off due to engine running rich meaning not meeting golden air:gas ratio of 14.6:1 so fuel residue in chamber continue to burn for the last moment. The same rich fuel problem that was why you had to let gas off during acceleration. Need to Check out the O2 sensor Check out MAP sensor Good luck

Sep 13, 2009 | 1997 Jeep Grand Cherokee

1 Answer

2003 Jeep Liberty check engine and security Light


CK the mass air flow sensor. First sensor on duct coming out of air filter.

Jun 13, 2009 | 2005 Jeep Wrangler

1 Answer

Fuwl pump runs for three seconds and stops


The relay is supposed to run for a few seconds to bring the fuel pressure up to specifications,,then shuts off again,,this is normal behavior in most cars with electric fuel pumps.
When you start the vehicle, the pump will cycle on again and shut it'self down when it needs to.

Jan 19, 2009 | 1997 Jeep Tj

1 Answer

My idle is all over the place!


Have you tried cleaning out the throttle body and injectors with a cleaner?

Nov 05, 2008 | 1997 Jeep Tj

3 Answers

2000 jeep cherokee starts then stalls in approx 3 sec 4.0 has new crank sensor


I am going to assume that it will not run even if you push on the accelerator pedal?
Can you install or attach an old timing light to the spark plug wires, turn it one and try to start it. The light should flash with the engine running, but if it shuts off at time of engine die, and the engine is still spinning, you are losing spark, My suggestion is the cranks shaft sensor on bell housing.
Second, install a pressure gage on the test port on the fuel rail and watch it as you start the engine, fuel pressure should not drop as the engine dies, if it does, the pump is not working correctly. There are two modes of power to that pump, one to start and timed, for only a few seconds to prime the system, and one to run continuously. Find the wires going to the pump at the tank. Connect test light to those wires and watch what happens during crank and at stall, You should not have the pump shut off and the engine dies.
If you have spark, and fuel pump working, when did you last change the filter,,but I put that LAST.
It has to be one or the other of these.
Good Luck

Aug 04, 2008 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...