Spark from coil to distributor but no spark on plugs. camry 300sei 1994 model.

Question 1

0answers

1994 camry cranks but wont start replaced ecu, coil, fuel pump, spark plugs, distributor and cap, spark plug wires, filtwers

Be the first to answer Apr 24, 2018 • Cars & Trucks

0helpful

1answer

1993 Camry 300sei v6. Spark from coil to distributor but no spark on plugs. I have replaced the ignitor with no results.Can the immoboliser be at fault?

is your ignition coil is OK?if fine , do you check the injector pulse if same no output ,

Sep 24, 2013 • 1993 Toyota Camry V6

1helpful

1answer

I do have a 1993 Camry 300sei (v6) Is the 1994 model the same?

This engine will probably have a cast iron block, painted black. Depending on which country you are in, some year from 1994 on Toyota changed the V6 to a design with an aluminium block, the 1MZ engine. So have a look to see what the engine block is made of.

Sep 24, 2013 • 1993 Toyota Camry V6

0helpful

1answer

Sluggish/sputtering while driving, then comes right, intermittent

Check the ignition coil,This is inside your distributor,right where the tower is its probaly cracked,

Mar 08, 2012 • 1994 Toyota Camry

2helpful

1answer

I cannot find the spark plugs on my camry !!!

First, you didn't mention which engine your 1994 Toyota Camry is equipped with. (This is really MUST-KNOW information if you want help with fixing your car.) There is a 3.0L V-6 engine and a 2.2L 4-Cylinder engine. Two TOTALLY different animals! I'll just take the extra time to answer for BOTH of them....

If your Camry is equipped with a 3.0L V-6 engine, You cannot find the spark plug wires because there are none, That engine is equipped with Coil On Plug (COP) ignition. The coils on the left bank (the side of the engine near the radiator) are located under the plastic cover on top of the engine. The coils for the right bank (the side of the engine near the firewall) are located under the upper intake plenum. The plenum MUST be removed to access them. (this is also required to replace the spark plugs.)

If you have the 2.2L 4-cylinder engine, the wires run down the center of the valve cover and the boots go down through the valve cover to the plugs. The other end of the wires attach to the distributor cap at the rear (drivers side) of the engine.

Jul 25, 2011 • 1994 Toyota Camry

0helpful

1answer

ENGINE TURNS OVER BUT WILL NOT START WHAT COULD THE PROBLEM BE

Is there a check engine light?

Sensors. Use a code reader of a jumper to read codes from your check engine light. Here's some help.
http://www.2carpros.com/kpages/first_things.htm

No check engine light.

Fuel pump or fuel filter. Try to start it, then pull a spark plug and see if you have gas on the plug or just the smell of gas. If you do it probably OK. If you don't, a new fuel filter, then a pump.

Ignition coil, Igniter or Distributor. Pull a spark plug and plug it back into it's spark plug wire. Turn over the motor and see if there's spark. You might need a helper or do it at night. There should be a small blue spark in the spark plug gap. Don't touch it. No spark...bad.
A lot of Toyotas use the same igniter so they are cheap at the junk yard and easy to fix.
Some distributors have the coil in them, some are do not. Check the external coil for spark. If there is none replace it. There are tests that can be made, but you need a book for that. A 1994 Camry probably has miles on it ,so anything you replace is good for an old car. Just don't buy from the dealer. You can get deals on line or at a junk yard.

Aug 15, 2010 • 1994 Toyota Camry

0helpful

1answer

Where are sparkplugs located on the camry? want to do my own tune up.

SPARK PLUGS IN THE CYLINDER HEAD.FOLLOW SPARK PLUGS WIRES.THEY WILL LEAD YOU TO THEM.BE SURE CHANGE PLUG WIRES DISTRIBUTOR CAP AND ROTOR IF EQUIPPED.SOME MODELS HAD DISTRIBUTORLESS IGNITION SYSTEM.

Jun 30, 2010 • 1994 Toyota Camry

1helpful

1answer

My 1994 toyota camry ,just quit running,it won't start,it will crank ,getting fuel,timing belt is moving what could be the problem

The coil pack may be bad, it will turn over and get fuel, but if the coil don't send spark to the plugs, it will not start. These can be checked by a local parts store and easily replaced by you. Or if you want, you can check to see if you're getting spark. It's not the best way to check but it works. Take one of the plug wires off the plug. Insert a sizable screwdriver in the wire, hold the screwdriver about 1/4" from a metal ground surface while someone turns the engine over. If you see spark, then the coil is good, and the problem lies somewhere else such as the distributor. If no spark the coil most likely is the problem.

Apr 30, 2010 • 1994 Toyota Camry

0helpful

2answers

I can not get my car to start

Most common,if you gave a distributor, is the ignition coil. The meter readings will be normal but the have a habit of getting small cracks in them that short to ground.

Apr 16, 2009 • 1994 Toyota Camry

0helpful

2answers

1994 toyota camery 2.2 eng. no spark at plugs. I have already replaced ignition module, still no spark. Everything else seems to be ok, eng. turns over good timing belt is intact ect... The car just shut...

check the ignition switch

Jul 18, 2008 • 1994 Toyota Camry

Question 2

molybdenum vann3

Expert 203 Answers
Posted on Sep 24, 2013

molybdenum vann3

Expert

Joined: Aug 06, 2013

Answers

203

Questions

8

Helped

43277

Points

637

Check the distributor cup or distributor rotor

Answer 2 · 3/6/2010 12:00:00 AM

Greg Bernett

2993 Answers
Posted on Mar 06, 2010

SOURCE: how to remove spark plug wires from the

Please don't forget to rate!

Disconnect the negative battery cable.
Label and disconnect the wires from each spark plug one at a time.
Remove the spark plug wires from the distributor cap. On some models you may need to use a flat bladed tool to lift up the lock claw and disconnect the holder from the cap. Separate the wires at the grommet.

Make sure to remove the spark plug wires from the boot end and NOT from the wire itself

Lift up the lock claw and disconnect the holder from the cap

WARNING Do NOT pull on the plug wires to remove them, this may damage the conductor inside.

Pull the plug wires from the retaining clamps.

To install:

Attach the holder and grommet portion to the distributor cap. Make sure that the holder is installed correctly to the grommet and cap.

Align the spline of the cap with the spline groove of the holder

Make sure the holder is correctly installed to the grommet

Check that the lock claw of the holder is engaged by lightly pulling on the holder.
On the center cord, insert the grommet and holder together.
Secure the wires with the clamps.

Anonymous

2 Answers
Posted on Aug 27, 2008

SOURCE: 1994 toyota camery 2.2 eng. no spark

had the same problem, replaced coil problem was solved

Anonymous

1 Answer
Posted on Oct 31, 2008

SOURCE: 94 toyota camery no spark

I had the same problem recently but replacing the ignition Coil under the distributor (inside) solved the problem. Also replaced the distributor Cap and rotor at the same time.

Anonymous

1 Answer
Posted on Mar 24, 2009

SOURCE: 1994 Toyota Camry Won't start.

you should check 3 things. AIr, Fuel, and "spark"
your cars could have many problems. Ignition module, fuel injectors, Mass Airflow Sensor.
You should check into all of these 3 things.
a crank-no start could be many things.
it could even be a cam positions sensors resistance going up when the engine heats up. Cracnk- no start means testing. n like i said
The motor is getting Air, There is Fuel being put into the cylinders, and the Spark plugs are firing.

Anonymous

266 Answers
Posted on Jun 20, 2009

SOURCE: No spark on my toyota camry. Changed coil pack and

what about wires pull the wires from the plug and make sure u got fire u need to see where ur loosing ur fire if u got it there pull from other end make sure u got fire off of coli pack its either or

Answer 3 · 3/6/2010 12:00:00 AM

Greg Bernett

2993 Answers
Posted on Mar 06, 2010

SOURCE: how to remove spark plug wires from the

Please don't forget to rate!

Disconnect the negative battery cable.
Label and disconnect the wires from each spark plug one at a time.
Remove the spark plug wires from the distributor cap. On some models you may need to use a flat bladed tool to lift up the lock claw and disconnect the holder from the cap. Separate the wires at the grommet.

Make sure to remove the spark plug wires from the boot end and NOT from the wire itself

Lift up the lock claw and disconnect the holder from the cap

WARNING Do NOT pull on the plug wires to remove them, this may damage the conductor inside.

Pull the plug wires from the retaining clamps.

To install:

Attach the holder and grommet portion to the distributor cap. Make sure that the holder is installed correctly to the grommet and cap.

Align the spline of the cap with the spline groove of the holder

Make sure the holder is correctly installed to the grommet

Check that the lock claw of the holder is engaged by lightly pulling on the holder.
On the center cord, insert the grommet and holder together.
Secure the wires with the clamps.

Answer 4 · 8/27/2008 12:00:00 AM

Anonymous

2 Answers
Posted on Aug 27, 2008

SOURCE: 1994 toyota camery 2.2 eng. no spark

had the same problem, replaced coil problem was solved

Answer 5 · 10/31/2008 12:00:00 AM

Anonymous

1 Answer
Posted on Oct 31, 2008

SOURCE: 94 toyota camery no spark

I had the same problem recently but replacing the ignition Coil under the distributor (inside) solved the problem. Also replaced the distributor Cap and rotor at the same time.

Answer 6 · 3/24/2009 12:00:00 AM

Anonymous

1 Answer
Posted on Mar 24, 2009

SOURCE: 1994 Toyota Camry Won't start.

you should check 3 things. AIr, Fuel, and "spark"
your cars could have many problems. Ignition module, fuel injectors, Mass Airflow Sensor.
You should check into all of these 3 things.
a crank-no start could be many things.
it could even be a cam positions sensors resistance going up when the engine heats up. Cracnk- no start means testing. n like i said
The motor is getting Air, There is Fuel being put into the cylinders, and the Spark plugs are firing.

Answer 7 · 6/20/2009 12:00:00 AM

Anonymous

266 Answers
Posted on Jun 20, 2009

SOURCE: No spark on my toyota camry. Changed coil pack and

what about wires pull the wires from the plug and make sure u got fire u need to see where ur loosing ur fire if u got it there pull from other end make sure u got fire off of coli pack its either or

Related Topics:

Trustworthy Expert Solutions

Spark from coil to distributor but no spark on plugs. camry 300sei 1994 model.

1 Answer

molybdenum vann3

5 Related Answers

Greg Bernett

Anonymous

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

1994 camry cranks but wont start replaced ecu, coil, fuel pump, spark plugs, distributor and cap, spark plug wires, filtwers

1993 Camry 300sei v6. Spark from coil to distributor but no spark on plugs. I have replaced the ignitor with no results.Can the immoboliser be at fault?

I do have a 1993 Camry 300sei (v6) Is the 1994 model the same?

Sluggish/sputtering while driving, then comes right, intermittent

I cannot find the spark plugs on my camry !!!

ENGINE TURNS OVER BUT WILL NOT START WHAT COULD THE PROBLEM BE

Where are sparkplugs located on the camry? want to do my own tune up.

My 1994 toyota camry ,just quit running,it won't start,it will crank ,getting fuel,timing belt is moving what could be the problem

I can not get my car to start

1994 toyota camery 2.2 eng. no spark at plugs. I have already replaced ignition module, still no spark. Everything else seems to be ok, eng. turns over good timing belt is intact ect... The car just shut...

Not finding what you are looking for?

1994 Camry

1994 camry cranks but wont start replaced ecu, coil, fuel pump, spark plugs, distributor and cap, spark plug wires, filtwers

Ask a Question

Check Out the Latest Top Trucks Report!

Top Toyota Experts

ZJ Limited

Thomas Perkins

ROBERT GARCIA

Are you a Toyota Expert? Answer questions, earn points and help others

Manuals & User Guides

.facebook_1762604185.jpg....

Related Topics:

Trustworthy Expert Solutions

Spark from coil to distributor but no spark on plugs. camry 300sei 1994 model.

1 Answer

molybdenum vann3

5 Related Answers

Greg Bernett

Anonymous

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

1994 camry cranks but wont start replaced ecu, coil, fuel pump, spark plugs, distributor and cap, spark plug wires, filtwers

1993 Camry 300sei v6. Spark from coil to distributor but no spark on plugs. I have replaced the ignitor with no results.Can the immoboliser be at fault?

I do have a 1993 Camry 300sei (v6) Is the 1994 model the same?

Sluggish/sputtering while driving, then comes right, intermittent

I cannot find the spark plugs on my camry !!!

ENGINE TURNS OVER BUT WILL NOT START WHAT COULD THE PROBLEM BE

Where are sparkplugs located on the camry? want to do my own tune up.

My 1994 toyota camry ,just quit running,it won't start,it will crank ,getting fuel,timing belt is moving what could be the problem

I can not get my car to start

1994 toyota camery 2.2 eng. no spark at plugs. I have already replaced ignition module, still no spark. Everything else seems to be ok, eng. turns over good timing belt is intact ect... The car just shut...

Not finding what you are looking for?

1994 Camry

1994 camry cranks but wont start replaced ecu, coil, fuel pump, spark plugs, distributor and cap, spark plug wires, filtwers

Related Topics

Ask a Question

Popular Questions

How to fix diagnostic code p0442

Electric front seat stuck

I have relay saying :mg clt what is that mean?

Starter making whining noise

VSC Trac off lights on dashboard

Check Out the Latest Top Trucks Report!

Top Toyota Experts

ZJ Limited

Thomas Perkins

ROBERT GARCIA

Are you a Toyota Expert? Answer questions, earn points and help others

Manuals & User Guides

.facebook_1762604185.jpg....