Question about 2007 Suzuki Grand Vitara 4WD

1 Answer

Headlight ajustment headlight beam to low need to adjust to make it higher to enable to see further than approx 100yds

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust headlight aim on nissan note


On the back of each headlight there are two adjusting screws, one will control the up and down the other controls left and right. To get the aim approx right without the optical set. Make sure the car is sat level, tyres at correct pressure, no heavy weight in the trunk. Drive the car up to a wall or garage door and with a piece of chalk/marker pen make a cross level with the centre of the headlight. Now move the car straight back approx six feet, switch headlights on main beam, the beam should centre on the cross, switch to low beam and the beam should move to the left and down by about 5cm

fca5e1f5-0584-406d-bd08-9f21451573c7.gif

Jan 01, 2014 | Cars & Trucks

1 Answer

How do you adjust headlight on 2008 uplander


If you look at the top of the head light assembly with the hood open just past the top rubber seal, you will see an alan head adjustor screw. This will adjust the low beam light up and down. the high beams are fixed. I would suggest shining your headlights on to a wall or garage door to get them to the same hight you need.

I am assuming that the design was not changed from my 2005 updander to your 2008. I had to adjust mine while on a road trip. We had a lot of people and stuff in my vehicle which made the headlights shine higher than normal. I was getting a lot of on commig traffic flashing. I was able to ajust them down fairly easy with those adjustor screws. Hope this helps.

Nov 30, 2010 | 2005 Chevrolet Uplander

1 Answer

How do i ajust the headlights on my 2005 ford ranger?


courtesy of expert super__guy

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 20, 2009 | 2005 Ford Ranger

5 Answers

How do i adjust my headlingt on a 2001 suzuki xl7


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 14, 2009 | 2001 Suzuki Xl 7

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

1 Answer

2004 ford focus headlight ajust ment


Your adjustment screws should be white nuts (adjustable with an allen wrench, or a socket, or a pair of pliers) located behind the headlamp assembly right up against the fender

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. You only need to do this and the aiming for your low beams as your high beams are on the same bulb

Your headlights should also say VOR. When you turn on your headlights, aim them right at the mark that you put on the wall, with the brightest cutoff directly under the mark

Sep 18, 2009 | 2004 Ford Focus

3 Answers

How do you adjust the headlights on a bmw 523I


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 02, 2009 | 2007 BMW 525xi Sedan

2 Answers

I have a 1998 landrover freelander how do i adjust the headlights ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 14, 2009 | 2004 Land Rover FreeLander

1 Answer

Headlights needs ajusting


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Mar 14, 2009 | 2004 Nissan XTerra

1 Answer

Headlight adjustment for 2006 Infiniti M35


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Feb 04, 2009 | 2006 Infiniti M35

Not finding what you are looking for?
2007 Suzuki Grand Vitara 4WD Logo

370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...