Question about 1993 Mazda RX-7

1 Answer

Pulling out gearbox rx7 rotary, but it wont pull out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Had same problem.....STOP...you have to get under car,there on the bellhousing you will find an inspection plate about 4 inches long,remove the retaining bolts and plate and you should be able to see the clutch and flywheel,look carefuly and you will see the pressure plate bolts, the ones that hold the clutch/pressure plate to the flywheel (6 if i remember), remove these, you will have to rotate the engine to get access to them one at a time, then when all are removed it should come apart easily.its a strange one because it leaves the pressure plate attached to the gear box( japs eh!),i can assure you that this is correct and there is a simple way to get the plate off by simply prising a washer forward and pulling plate free from gearbox.......simple when you know how....(i almost used a jeep and chain to pull my engine/gearbox apart before i was shown how to do it)
i know ,not hope this will help!
have fun and regards....
dave

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I restore compression on a 88 Mazda rx7


If low compression it would need a rebuild.

Mar 28, 2013 | Cars & Trucks

1 Answer

I have a rx7 series 5 13 B turbo motor the car starts and runs really well but once the car warms up its starts smoking and increases then after driving it the smoke starts to die down alot


The side seals for the rotors are bad. the only thing you can do is pull the engine apart and replace the seals IF the side housings are good. If they are bad, you cant machine them, they are JUNK. Find a shop that rebuilds Mazda Rotary engines. Mazda may be the best place to get a reman engine.

Sep 13, 2011 | 1987 Mazda RX-7

1 Answer

Where is the clutch located on a mazda rx7 1986? i need too change the clutch since the clutch went out?


The clutch assembly is located inside the 'bell-housing' which is the flared forward section of the gearbox. Hence, the tailshaft and gearbox need be removed to inspect clutch condition.

Oct 31, 2010 | 1986 Mazda RX-7

1 Answer

13B Rotary Firing order diagram


The 1984 Mazda RX7 has a Rotary Engine.
For the 1.1L

Firng Order:
1-2 (thats all folks!)
Cylinders:
__________
'......2.......'
'......1.......'
....[FAN]

Distributor:
.............(+)-screw
......2
1..........2
......1
(+)-screw

Aug 09, 2010 | 1984 Mazda RX-7

1 Answer

My 1984 rx7 starts when choke is pulled out. WHen


Your carberater is having problems getting the correct amount of fuel.Either a line or fuel filter is clogged or you need to have your carb. rebuilt.

Apr 26, 2010 | 1983 Mazda RX-7

1 Answer

I have a 1989 mazda rx7 convertible automatic with the 13b rotary engine and im going to swap the engine and tranny for the 13b turbo engine and manual tranny,and also have ecu.is it hard to swap and how.


its not hard at all. as long as your good with your hands. and know the basics of your rx7. other then that everything bolts in. you just need a turbo driveshaft for sure. or they sell a custom driveshaft on mazdatrix.com so you can keep your N/A differential.

Apr 18, 2010 | 1989 Mazda RX-7

2 Answers

Im pulling the gearbox out of my 1995 Mazda Rx7 and it wont come off the spline? its stuck


did you disconnect the slave cylinder for the clutch? If its an automatic you must unbolt the torque converter.

Also check for extra bolts and mounts that may hold the transmission in.

Jul 10, 2009 | 1993 Mazda RX-7

1 Answer

What Seal kit for 2nd gen Rx7 FC Turbo II FC3S???


I would just replace the APEX seals because they are cheaper BUT unless you know alot about the rotary i wouldnt take the motor apart your self i would take it to someone and have then do it because the rotary motor is very tedious and everything almost has to be perfect.

Jun 09, 2009 | 1991 Mazda RX-7

5 Answers

Motor


Yes it does, that is the only engine option.

Mar 03, 2009 | 1987 Mazda RX-7

Not finding what you are looking for?
1993 Mazda RX-7 Logo

Related Topics:

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...