Question about 1993 Honda Accord

1 Answer

94 accord can't remove bolt at crankshaft to replace timing belt

I have tryed everything even bought the tool that honda says to do it with. Used a 1" impack hammer will not move is there something that I am missing

Posted by on

  • 1 more comment 
  • Duane Peterson Apr 19, 2009

    Crankshaft bolt

  • Richard Camp
    Richard Camp May 11, 2010

    What bolt are you trying to remove? Thanks, RAC

  • yadayada
    yadayada May 11, 2010

    the bolt is reverse thread?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Yes.... that bolt turn opposite the normal direction to remove a bolt.

Posted on Apr 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace Crank Seal , Honda Accord 95, F22B2 engine


this is covered in the FSM. 95 accord.
did you google this?
http://www.honda-acura.net/forums/accord/137349-1993-f22-crank-cam-balance-shaft-seal-hell.html

are you sure its only the crank seal,????
gravity lies. as does windage effects.
is this an A/T or M/T car, the latter makes the bolt come off easy
(5th gear + brakes) the slush pump tranny NOT.
so if you read the FSM it states." it shows photo of tire off and pulley bolt view and how the body ends just above that bolt, (see it?)
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. If necessary, secure the crankshaft with a flywheel holding tool.
For some engines, a special pulley holder tool is available to secure the pulley while removing and installing the bolt (refer to the illustration)."
4 Remove the crankshaft pulley bolt. This bolt can be difficult to remove. Spray the bolt with penetrating oil and allow it to soak overnight. Book forgets to see CCW direction on bolt (RHT)
the bolt will take about 200fl/lbs of reverse torque to get off.
5 Carefully remove the pulley from the crankshaft. Do not pry it off.
6:
Remove the key from the crankshaft sprocket. Be sure not to lose it.
7 -If necessary, remove the tool holding the crankshaft.

remove seal with seal puller or screw trick ,etc.
do not damage the seal base collar of the housing. DO NOT.

is this your first engine seal work>?
or done many , just need help with one honda.?
if doing all work on a honda, did you ever consider a real FSM?
why not get one, and read it, and all the steps and warnings.
worst case.
if you work engines, you know as you go , you see
Omg, it not the crank it the cam leaking, or just a bad valve cover.
fate happens, distributor seal leak too.

with all FWD, doing a crank seal can be easy or hard.
no access panels in finder
or on some cars, 7ton pressed on pulley, (Dodge neons/ yuk)

bolt spec:
1994-95 Accord and Prelude-181 ft. lbs. (245 Nm)

if the 90,000 mile timing belt is ignored, you will bend the head valves over, or worse... so...... all this , is a consideration.

Feb 25, 2014 | 1995 Honda Accord

1 Answer

Need to know how to replace the belts on a 1992 Honda accord.


How to dismantling and change timing belt for CB7 engine:
1. remove elektrik power (+) from accumulator
2. put suport on below engine
3. remove the bolt and left engine mounting
4. remove upper engine cover
5. open side engine cover (timing cover from black plastic)
6. please remember top marking on the crankshaft
7. make to slack tensioner wheel, and remove the belt.

note : there are two timing belt on cb7 engine, smaller and bigger

you can try
my number call +6281808024008 (Dede)

Jul 12, 2011 | 1992 Honda Accord

1 Answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?


check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif

Oct 29, 2010 | 2000 Honda Accord

1 Answer

Installing a timing belt


Timing Belt and Sprockets REMOVAL & INSTALLATION Fig. 1: If you plan on reusing the timing belt, make sure you note the direction of the rotation before removal 91053p69.jpg Fig. 2: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts 91053p10.jpg Fig. 3: Camshaft alignment using the special service tool 91053g61.gif Fig. 4: Insert the crankshaft damper bolt to turn the crankshaft and . . . 91053p64.jpg Fig. 5: . . . align the camshafts and the . . . 91053g64.gif Fig. 6: . . . crankshaft before removing the old belt 91053p66.jpg Fig. 7: Loosen the timing belt tensioner pulley bolt, slide the tensioner back and . . . 91053p67.jpg Fig. 8: . . . tighten the bolt to the farthest right hand side as possible to hold the release the tensioner pulley so that the belt can be removed 91053p68.jpg Fig. 9: . . . remove the belt starting from around the camshaft pulleys 91053p01.jpg Fig. 10: Installation of the tensioner spring and retaining bolt 91053g62.gif For information on timing belt recommended replacement interval, refer to Section 1. CAUTION
The 2.0L engine is an interference motor. Extending the replacement interval could lead to the belt breaking and severe and costly engine damage. Care must be taken if rotating the crankshaft or camshafts with the belt off, if resistance is felt, do not force them to turn.
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers as outlined in this Section.
  3. Remove the valve cover.
  4. Place Camshaft Alignment Timing Tool T94P-6256-CH or equivalent, into the slots of both camshafts at the rear of the cylinder head to lock the camshafts into position. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  5. Loosen the camshaft timing belt tensioner pulley retaining bolt and move the tensioner pulley to relieve the tension on the timing belt.
  6. Temporarily tighten the tensioner in this position. NOTE: If the timing belt is to be reused, mark the belt for the direction of rotation before removing to prevent premature wear or failure.
  7. Remove the timing belt.
  8. If required, remove the sprockets as follows:
    1. Hold the camshaft with an appropriate camshaft sprocket holding tool.
    2. Loosen and remove the camshaft sprocket retaining bolt.
    3. Remove the sprocket from the camshaft.
    4. Repeat the procedure for the 2nd camshaft sprocket.
    5. Remove the crankshaft sprocket.
  9. Slide the crankshaft sprocket onto the crankshaft aligning the key-way.
  10. Align the camshafts using the Camshaft Alignment Timing Tool T94P-6256-CH. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  11. Reinstall the sprockets onto the camshafts and loosely install the camshaft retaining bolts.
  12. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  13. Loosely install the crankshaft pulley to verify that the engine is at TDC. Realign the marks if they have moved.
  14. Verify that the camshafts are aligned. NOTE: It is recommended to purchase a tensioner spring and retaining bolt through the dealer parts to apply the proper tension for used or new belt installations. The spring is bolted to the tensioner assembly and becomes a part of the engine. Ignore this notice if the tensioner spring is already installed.
  15. Reinstall the retaining bolt (W700001-S309) into the hole provided in the cylinder block and place the tensioner spring (6L277) between the bolt and the camshaft timing belt tensioner pulley.
  16. Tighten the retainer bolt to 71–97 inch lbs. (8–11 Nm) .
  17. Remove the crankshaft pulley and install the timing belt onto the crankshaft sprocket, then onto the camshaft sprockets working in a counterclockwise direction.
  18. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  19. Be sure that the span of the camshaft timing belt between the crankshaft sprocket and the exhaust camshaft sprocket is not loose.
  20. Be sure that the camshaft timing belt is securely aligned on all sprockets.
  21. Reinstall the lower timing belt cover and tighten the retaining bolts to 53–71 inch lbs. (6–8 Nm) .
  22. Apply silicone sealer to the key-way of the crankshaft pulley and install. Tighten the retaining bolt to 81–89 ft. lbs. (110–120 Nm) .
  23. Inspect the timing mark on the crankshaft pulley to verify that the engine is still at TDC.
  24. Loosen the camshaft timing belt tensioner pulley retaining bolt and allow the tensioner spring attached to the pulley to draw the tensioner pulley against the camshaft timing belt.
  25. Remove the camshaft alignment timing tool from the camshafts at the rear of the engine.
  26. Turn the crankshaft two revolutions in a clockwise direction.
  27. Tighten the camshaft timing belt tensioner pulley retaining bolt to 26–30 ft. lbs. (35–40 Nm) .
  28. Recheck that the crankshaft timing mark is at TDC for the No. 1 piston, and that both camshafts are in alignment using the camshaft alignment timing tool. NOTE: A slight adjustment of the camshafts to allow the insertion of the camshaft alignment timing tool is permissible as long as the crankshaft stays at the TDC location.
  29. An appropriate camshaft sprocket holding tool can be used to move the camshaft sprocket (s) if a slight adjustment is required.
  30. If a camshaft is not properly aligned, perform the following procedure:
    1. Loosen the retaining bolt securing the sprocket to the camshaft while holding the camshaft sprocket from turning with the sprocket holding tool.
    2. Turn the camshaft until the camshaft alignment timing tool can be installed.
    3. Verify that the crankshaft timing mark is at TDC for the No. 1 cylinder.
    4. While holding the camshaft sprocket with the camshaft sprocket holding tool, tighten the retaining bolt to 47–53 ft. lbs. (64–72 Nm) .
    5. Remove the tool and rotate the crankshaft two revolutions (clockwise) .
    6. Verify that the camshafts are aligned and that the crankshaft is at TDC for the No. 1 cylinder.
  31. Install the valve cover.
  32. Install the timing belt covers.
  33. Connect the negative battery cable. prev.gif next.gif

Aug 17, 2010 | 2000 Mercury Mystique

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

1 Answer

Timming belt broke on 93 plymouth lazer and need instalation directions


It is recommended that the timing belt be replaced periodically to assure correct engine performance. Because of their composition, timing belts wear over a period of time and mileage. To avoid vehicle break down and possible engine damage, the manufacturer recommends timing belt replacement at 60,000 miles.
REMOVAL & INSTALLATION1.8L Engine
See Figures 1, 2 and 3
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt.
6dd1bcf.jpg

Fig. 1: Silent shaft belt timing marks-1.8L engine

b474c8c.jpg

Fig. 2: Checking the silent shafts for proper positioning

1b23c0f.jpg

Fig. 3: Timing belt timing mark alignment-1.8L engine

To install:
  1. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  2. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1 / 4 in.
  3. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  4. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  5. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover.
There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  1. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  2. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  3. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  4. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  5. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  6. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1 / 2 in.
  7. Install the timing belt covers and all related items.
  8. Connect the negative battery cable.
2.0L Engine
1990-94 VEHICLES
See Figures 4, 5, 6 and 7
  1. Disconnect the negative battery cable.
  2. Remove the timing belt upper and lower covers.
  3. Rotate the crankshaft clockwise and align the timing marks so No. 1 piston will be at TDC of the compression stroke. At this time the timing marks on the camshaft sprocket and the upper surface of the cylinder head should coincide, and the dowel pin of the camshaft sprocket should be at the upper side.
Always rotate the crankshaft in a clockwise direction. Make a mark on the back of the timing belt indicating the direction of rotation so it may be reassembled in the same direction if it is to be reused.

  1. Remove the auto tensioner and remove the outermost timing belt.

1f685f2.gif

Fig. 4: Exploded view of the timing belt and sprockets-1990-94 2.0L engines

  1. Remove the timing belt tensioner pulley, tensioner arm, idler pulley, oil pump sprocket, special washer, flange and spacer.
  2. Remove the silent shaft (inner) belt tensioner and remove the belt.
  3. Remove the crankshaft retaining bolts, then remove the pulley.
  4. Remove the crankshaft sprocket retainer bolt and washer from the sprocket, if used, and remove the sprocket. If the sprocket is hard to removed, the proper puller may be used. If no bolts are used on the sprocket. Use the correct puller to remove.
  5. Hold the camshaft stationary using the hexagon cast between journals No. 2 and 3 and remove the retainer bolt. Remove the sprocket from the camshaft.

To install:
  1. Install the sprockets to their appropriate shafts. Install the retainer bolts and tighten the camshaft sprocket bolt to 65 ft. lbs. (90 Nm).
  2. Check both tensioner and idler pulley for bearing wear, and replace if needed.
  3. Align the timing marks on the crankshaft sprocket and the silent shaft sprocket. Fit the inner timing belt over the crankshaft and silent shaft sprocket. Ensure that there is no slack in the belt.

79a47c7.jpg

Fig. 5: Align the camshaft sprocket so marks face each other and are in alignment with the top surface of the cylinder head-1990-94 2.0L engine

54d0ef5.jpg

Fig. 6: Align the crankshaft timing mark and the oil pump sprocket timing mark-1990-94 2.0L engine

73f137d.jpg

Fig. 7: Timing marks in alignment-1990-94 2.0L engine

  1. While holding the inner timing belt tensioner with your fingers, adjust the timing belt tension by applying a force towards the center of the belt, until the tension side of the belt is taut. Tighten the tensioner bolt.
When tightening the bolt of the tensioner, ensure that the tensioner pulley shaft does not rotate with the bolt. Allowing it to rotate with the bolt can cause excessive tension on the belt.
  1. Check belt for proper tension by depressing the belt on its' long side with your finger and noting the belt deflection. The desired reading is 0.20-0.28 in. (5-7mm). If tension is not correct, readjust and check belt deflection.
  2. Install the flange, crankshaft and washer to the crankshaft. The flange on the crankshaft sprocket must be installed towards the inner timing belt sprocket. Tighten bolt to 80-94 ft. lbs. (110-130 Nm).
  3. To install the oil pump sprocket, insert a Phillips screwdriver with a shaft 0.31 in. (8mm) in diameter into the plug hole in the left side of the cylinder block to hold the left silent shaft. Tighten the nut to 36-43 ft. lbs. (50-60 Nm).
continue...

Sep 09, 2009 | 1993 Plymouth Laser

1 Answer

1991 Accord 2.2L timing belt replacement


Hi,
yes standard right hand thread,the easiest way is with a very powerful air gun with an impact socket,be warned have had to use an 1 inch drive lorry gun to undo these bolts as have a compression washer under the bolt head,Good luck,

Aug 06, 2009 | 1991 Honda Accord

1 Answer

Leak from the water pump


  • first of all you are probably going to need a torque wrench for the crank shaft pulley bolt it has 225lbs.of torque or more.I just did one on my 1991 honda accord dx .you have to take off a/c belt ,alternator etc. on the crank pulley.(I took it to a shop and they heated the 3/4 in. bolt and used torque wrench. I broke a half inch breaker bar trying to get it offf) next use puller to take off crankshaft pulley.support motor and remove motor mount bracket. take off upper and lower timing belt covers.take off timing belt and other belt using the tensioners.take off and replace water pump CHECK ALL TIMING MARKS with #1 piston@TDC. There are about 6.

Jun 02, 2009 | 1991 Honda Accord

2 Answers

Honda accord ex 92


Crankshaft pulley (harmonic balancer) removal- disconnect neg battery cable, remove belts, it would be a good idea to soak the bolt w/ penetrating oil overnight, there is a special 'crankshaft pulley holding tool' available to secure the pulley while removing and installing the bolt. Some parts stores loan tools for free if u purchase parts from them, I don't know if this is available, but it would be worth checking out. Attach holding tool and remove bolt securing pulley. Carefully remove pulley from crankshaft, Do NOT pry off. Remove key from crankshaft sprocket,
Install: install key on crankshaft sprocket, slide pulley on, apply clean oil to bolt threads but NOT to washer contact surfaces, secure crankshaft w/ holding tool, tighten to 159 ft lbs (91-93 Accord), install belts, re-attach neg cable.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...