Question about 2000 Mercury Grand Marquis

1 Answer

How to install the window cable in the rear door

How to install a cable in power windows of the rear door of a 2000 Mercury Grand Marquis.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 43 Answers

The regulator cables come as an assembly. You need to replace the whole regulator.

Posted on Apr 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 grand marquis, only the two rear, electric windows don't work, is there something in common to cause this problem ?


One place to check would be to remove the trim from the lower part of the B-pillar (the part between the front and back doors, where the rear door hinges are) on the driver side. There should be a plug near the floor connecting the wiring from the main power window switch on the driver's door to the two rear doors.

Oct 03, 2016 | 2000 Mercury Grand Marquis

1 Answer

2000 mercury grand marquis passenger rear window, motor runs but window wil not go up & down.


Remove the inner door panel,see the problem,
replace the broken window regulator

Sep 20, 2013 | Mercury Grand Marquis Cars & Trucks

1 Answer

My 2000 Mercury Grand Marquis LCS the rear passenger doors electric window I was rolling it down & apprx. 1 1/4" to 2" before the bottom ( for window to be completely all the way down) it stopped &...


Power Window assemblY Needs replacing. I've had to replace my driver side assembly a few times over the years in my 97 accord after a wreck on that side. Something doesn't line up right anymore and it eventually causes it to wear out. Steel cable and plastic parts don't work real well together over time- that plastic can wear out. Tricky part can be getting the door panel off. From there it can be pretty straight forward. May need an extra set of hands to get the window just right to attach to the bracket on the regulator assembly. May find some useful videos online, even if it's for a different car it can give you a good idea.

Mar 31, 2017 | 2000 Mercury Grand Marquis

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How to install a new power window motor in my 1993 Mercury Grand Marquis? I have a 1993 Mercury Grand Marquis Ls and the power window doesn't work. So then I bought some new window motors and I was...


Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Sep 11, 2009 | 1993 Mercury Grand Marquis

1 Answer

Rear windows stuck in open position on 1996 mercury grand marquis


Check all fuses. If fuses are good replace the master window switch on the drivers door. Good luck

Mar 30, 2009 | 1996 Mercury Grand Marquis

1 Answer

2000 Mercury Grand RR door power window


you must replace window regulator as a unit

Sep 02, 2008 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
2000 Mercury Grand Marquis Logo

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...