Question about 1993 Ford F150 SuperCab

1 Answer

The ignition control module is not located on the side of the distributor were i was told it was.the truck was idling and it just died noew it turns over but wont fire off any ideas on other things to check besides the fuel filter .i already checked that out.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,164 Answers

Th4e module is on a heat sink on driver side inside fender. she photo of module
the ignition control module is not located on the - 6d7f7a3.jpg

Posted on Apr 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drives for a little then cuts off 30 min later starts then dies


could be
Starter
Spark plugs
plug wires
Distributor cap and rotor
Ignition control module
Ignition Coil
Fuel Filter

Feb 16, 2016 | Cars & Trucks

1 Answer

93 honda accord shuts off after reaching temp


I had the same problem with my accord years ago and it turned out to be that the ignition module would die whenever it got hot and then start working again when it cooled off. It is located inside the distributor and costs a bit less than a whole new distributor. I changed the entire distributor, to be sure all the ignition components were new and would not fail again for a while.

Aug 06, 2012 | 1993 Honda Accord

2 Answers

Locate the ICM on a 95 bronco 5.8L (ignition control module)


On 1995 Ford Truck Bronco 5.8L EFI 8cyl the Control Module-Ignition is located under hood, center, upper engine area, front of intake manifold, mounted on front side of distributor.

zjlimited_1625.jpg

Fig. 1: A TFI-IV ignition module



Hope this helps (remember to rate and comment this free answer).

Jul 26, 2011 | 1993 Ford Bronco

1 Answer

No spark Told to replace ignition control module where is it located


Your 95 Jeep does not have an ignition control module. This ignition system has a exterior mounted ignition coil and also a pick up switch inside the distributor.

Jan 02, 2011 | 1995 Jeep Grand Cherokee

1 Answer

89 k1500 towed, now fuel injectors dont fire. read all wired to and from ecm, check good. ecm will start another truck.


Check the ECM fuse and then check for any loose wire connectors, especially at the fire-wall area, the ignition coil, and the distributor. Then check for battery voltage at the positive side of the ignition coil when the ignition key is in the "On" or "Run" position, and there should also be battery voltage running over from a wire that is also connected to the positive side of the ignition coil, and then that wire will run over from the ignition coil to the ignition module inside of the distributor, and if there is battery voltage there at the ignition module, then either the ignition module or the pick-up coil inside of the distributor will be the most likely suspects for the cause of the problem.

The ignition module and the pick-up coil/stator located inside of the distributor is actually what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like it could also be a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

The same principal applies to HEI (High Energy Ignition) ignition systems with the ignition coil mounted in the top of the distributor cap.


1a01318.jpg

8d696cc.jpg

Sep 18, 2010 | 1989 Chevrolet K1500

2 Answers

Where is the ignition control module located on a 1995 mercury sable 3.0 v6


For 1995 Mercury Sable 3.0L EFI 6cyl the Control Module-Ignition is located: Under hood, center, upper engine area, mounted on side of distributor.

Hope helps (remember rated this).

Aug 11, 2010 | 1995 Mercury Sable

1 Answer

1979 chevy van not getting spark.was running fine day before.turns over fine,getting fuel.could it be the module


First thing is what condition are the distributor cap, ignition rotor, and spark plug wires in?

There is the possibility that the ignition coil located in the top of the distributor cap is faulty and first check to see if full battery voltage is even getting to the "Bat" or "Pos" (+) positive side of the ignition coil when the key is in the "Run" position. Then check the secondary resistance to the ignition coil.

The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil. A faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores. If the ignition module does test out alright then the problem could still be in the pick-up coil/stator, (it can be tested using an ohm meter by dis-connecting the wire connector from the pick-up coil/stator and the ohm reading between the two wires from the pick-up coil/stator should be between 500 and 1500 ohm's, and both of the wires from the pick-up coil/stator should show an open loop or an infinite reading between each wire and ground) and if the pick-up coil/stator is found to be faulty then replace the entire distributor, or the distributor will have to be dis-assembled to install a new pick-up coil/stator.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Let me know if you require any further assistance.


b0c4aa0.jpg

Jul 29, 2010 | 1979 Chevrolet C/K 3500

1 Answer

Truck will turn over but not start. Checked fuel flow up to injectors, all good but injectors were not spraying into throttle body. Changed Coil, wires, battery, fuel filter...even with all the adjustments...


The ignition module located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil. A faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Jun 22, 2010 | 1989 GMC Sierra

1 Answer

It starts and runs for a while, and then randomly dies and wont start, but starts again after sitting a few hours


That is the classic symptom of an electronic component overheating, and it could be a problem with the fuel pump, the ignition module inside of the distributor could be faulty, or the ECM (Engine Control Module) could be faulty, and the ECM's that were manufactured back then were prone to faults, and that is also why they can be purchased for only around $70.00 at most auto part stores.

The ignition module located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil. A faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

Jun 19, 2010 | 1984 Pontiac Fiero

Not finding what you are looking for?
1993 Ford F150 SuperCab Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...