Question about 2002 Jeep Grand Cherokee

1 Answer

How do u make sure if ur crank shaft censor is in time right

We just got done puttin a 05 motor in an 02 jeep grand cherokee laredo 4.0 v6, it cranks over but will not start, could this be due the crankshaft censor.

Posted by on

  • Richard Scordino May 11, 2010

    Also, make sure you did not bang flywheel into it when installing engine...they don't like that!

  • Richard Scordino May 11, 2010

    There should be no continuity between b&c terminals of the sensor (marked on harness plug) Check with an ohmeter. (reading on meter should be the same as if it is not connected to anything.) Also make sure that all body ground wires are connected. (don't forget block to firewall)

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

If the distributor syc is not set will cause the same problem

Posted on Apr 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

2 Answers

My car wont start after i changed the fuel filter wat is the problem 2000 jeep grand cherokee Laredo


keyon .off 5 times then start.
or crank for 5 seconds.
this will prime it
some cars dont prime with key on trick. only cranked.

Apr 20, 2015 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Just dies, sometimes won't start. Changed crank shaft censor, still no good


ihave a 98 grnd chrk lrdo had to replace computer on fire wall, periodicly i spray all electrical connections w/ crs electric contact spray.

Jun 01, 2012 | 2000 Jeep Grand Cherokee

2 Answers

1996 Jeep Grand Cherokee Laredo It sat


Try gently tapping the starter motor with a hammer or bar. There may be a bad contact in the sollenoid or the starter motor brushes worn to their limit. Tapping may give you a tempory fix if the problem lies in the starter motor.

Aug 12, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Locate crankshaft position/crank angle sensor


The crank posistion sensor is located on the top of the transmission bell housing right next to the motor, its a @$^&^ to get to and do without a lift,

Jul 02, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Jeep is hard to get started and dies when you put it in gear


First check battery condition, second was the syc set after install?

Apr 18, 2009 | 2002 Jeep Grand Cherokee

2 Answers

1993 JEEP GRAND CHEROKEE LAREDO IM TOTALLY BAFFLED


Back up a minute...Do you have spark from the coil wire? (juice from coil) If so, change or check rotor and cap (wires do not all go bad at same time so unless they are wet, likely at least good enough to start engine)

Mar 05, 2009 | 1993 Jeep Grand Cherokee

1 Answer

1999 Jeep Grand Cherokee Laredo won't run


if ur jeep has central lockin lock it and then unlock it ..........she might b sucking air inn

Feb 26, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...