Question about 2001 Isuzu Rodeo

1 Answer

Change 2001 rodeo shocks

I have no problem removing the bottom bolt but the top bolt I can not because the entire upper cylander of the shock spins when the bolt is turned. Any suggestions to keep the shock from spinning? Thank you.

Posted by on

  • Darren North Apr 18, 2009

    Haven't tried it yet but I think it will

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 234 Answers

If you are replacing the shocks anyway, you may be able to snap a vice grip on the shaft so that it won't spin.

Sometimes you can use a pipe wrench too.

If the vehicle is supported on the frame, it will expose more of the shaft.

Posted on Apr 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear struts 2002 saturn LS


Raise vehicle.
Remove tire and wheel assy.
Rmove inner wheelhouse liner ,5 bolts.
Remove the shock-to -knuckle bolt and discard.( Go get a new one). This is the bolt on the bottom of the shock.
Remove upper carrier assembly to body bolts ( top two bolts).
Loosen lower carrier assembly to body bolts until the carrier assembly slides out.
Then, using either a rented spring compressor, or get a pro to remove it for you. If you a rental, please please please look on YouTube to see how to use one properly.
Replace any worn out rubber components, they are sold separately.
Installation is in reverse order.
Torques: Top of shock absorber ,15 foot pounds
Rear carrier bolts, 40 foot pounds.
Bottom shock to knuckle, 110 foot pounds.

Source: Saturn Technical Service Manual , L Series, 2000-2001
Good Luck !!!

Mar 21, 2015 | Saturn LS Cars & Trucks

1 Answer

How to replace rear shocks


Removal & Installation

  1. Raise and safely support the vehicle.
  2. Support the rear axle and slightly lower the vehicle enough to lessen tension on the shock absorber.
  3. Remove the lower shock absorber retaining nut and washer.
  4. Disconnect the lower end of the shock absorber from the mounting stud.
  5. Remove the shock absorber upper end retaining nut and washer.
  6. Remove the shock absorber from the vehicle.
To install:
  1. Install the shock absorber onto the upper and lower mounting studs of the vehicle.
  2. Install the washers and retaining nuts. Tighten the upper and lower retaining nuts to 22-30 ft. lbs. (30-41 Nm) on 2001-02 models or 22 ft. lbs. (30 Nm) for the upper bolts and 47 ft. lbs. (64 Nm) on the lower bolts.
  3. Lower the vehicle.

Jul 07, 2014 | 2004 Nissan Quest

1 Answer

Rear shock absorber installation


Loosen and remove the upper nut and bolt. Compress the shock and wiggle it off the lower stud. Slide the new shock into place and tighten the lower nut. Pop the top of the shock into place and bolt the upper bolt through the holes the same way you removed it. Tighten the nus and bolt in the same point they were when you removed them. Then lower the car to the ground and you are done.lightdeal

May 28, 2013 | 2001 Pontiac Firebird

1 Answer

How to change front shocks


You'll need to remove the wheel. If it's 2 wheel drive, you'll need to hold the upper stud and remove the retaining nut, and bushings associated with it. On the bottom of the control arm you'll see 2 bolts that need removed, the shock will drop out. If it's 4 wheel drive, there will be an upper bolt and nut to remove, same for the bottom of the shock.

Mar 16, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

How replace the rear shocks on mercedes 420 sel


You will need to remove the rear seats to access the hole just above the shock. Remove the bottom seat cushion first, then find the small bolts that hold the upper seat to the frame. Once removed, you will see access to the top of the shocks (might have a plastic covering the hole).

Feb 14, 2010 | 1991 Mercedes-Benz 420

1 Answer

How to change shocks on a 2001 Yukon Denali


shocks??theres a bolt on top and on bottom of the strut called the shock mount bolt remove theme and the shock will come right out.to put new ones mount the top first its easier to push up on the shock to replace the bottom bolt

Dec 06, 2009 | 2007 GMC Yukon Denali

1 Answer

Is there a recommended way to replace the drivers side front shock on a 1999 Dodge ram 4x4 diesel


For shock removal and replacement is fairly easy -- first remove the top shock nut and then the three nuts on the tower surronding the upper shock nut - then remove the bottom through bolt and pull shock up through the top -- install in reverse order - (don't worry about the shock expanding after you get the bottom bolt back in, you can push the top of the shock down with the tower and secure it). recommend you replace both front shocks

Dec 01, 2009 | 1999 Dodge Ram

1 Answer

How to replace rear shocks on 96 bmw 328i


Inside the car carefully pry up the speaker covers off the rear parcel shelf and undo the two screws that secure the speaker assembly onto the shelf. Release the clip and carefully from inside the boot pull the speakers away and disconnect the speaker connections
Open the boot and remove the carpet from the rear "wall" by unscrewing the 4 retaining "nuts" at first by hand and then using a phillips screwdriver.
bootcarpet.jpg

Lift this out and lift out the floor carpet. Carefully pull the side carpets away from the boot interior. They are held in 3 places : on one of the retaining bolts by the rear carpet, by a metal ledge at the top near the rear lights and by the ledges on the plastic parts in the boot.

Jack up the car and chock the front wheels so it can't roll anywhere. Also put something underneath the wheels so they cannot drop down when you undo the shock mounts.
reartower.jpg
Using a 13mm socket undo the two top shock mounts ONLY once you have supported the wheels so that you dont put stress on the suspension arms. Pry off the rubber dust cover.
shocklwrbolt.jpg
Undo the lower shock retaining bolt and carefully lift the entire shock away from the car.
oldcompleteshock.jpg
The old knackered shock and shock mount!
undotopmount.jpg
You need to recover the lower cup, upper cup and bump-stop from the old shock. To do this you need to remove the top mount from the old shock. If you look at the top of the piston it has a flat section to it. Get a set of mole grips and clamp them onto the flat section, do this as tight as you can so that you dont round it and using and adjustable spanner undo the piston retaining nut whilst holding the piston shaft using the molegrips.
keepthesebits.jpg
You need to recover 3 pieces from the piston shaft. 1- the bump stop, 2 - lower cup, 3 upper cup. Using the new shock mount as a template cut out a gasket from cardboard (the box the mount came in is ideal) to go between the upper shock mount and the suspension tower. Incidently according to the haynes manual this is made of rubber but mine was made of card! under no circumstances put the upper shock mount directly into the suspension tower.
newshock2.jpg
Put the 3 pieces onto the new shock and tighten the piston nut to secure the shock mount and put your new gasket onto the upper mount.
reartowernoshock.jpg
Use the opportunity to clean the suspension turret - do the top and the underneath making sure it's all clean and dry.
Put the new complete assembled shock into the suspension tower and either get someone to do up the top bolts a few turns or rest the bottom of the shock in the inner circumference of the wheel and lift it into position by lifting it up using the piston nut and then do the bolts up a few turns.
Bolt the bottom shock bolts back into place after putting some nut-lock on the threads and tighten them up securely, then tighten up the top mount securing bolts and put on the rubber dust cap.
bootcarpet.jpg
Put the side carpets back in making sure the speaker cables aren't trapped behind, putting in the end nearest the tail lights first making sure it's behind the retaining ledge both at the top and the end. Then do the centre section and finally over the bolt at the rear of the boot. Put the rear carpet back in and do up the retaining nuts. Reconnect the speakers and engage the lip and push the speaker up until the clip clips into place and do up the securing screws and clip the speaker cover back on.

About What's New BMW In-Depth How To Pages My Projects Garage Sale Galleries Communities Links Contact Donate



















































































































Jul 07, 2009 | 1999 BMW 328 Series

1 Answer

Are their any speical problems or tricks in replacing air adjustable rear schocks on a 2001 buick custom


Removal & Installation

  1. Remove the tire and wheel assembly.
  2. Support the control arm with a jack stand.

    0900c152802427b0.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Use support bracket tool J-23028-01 mounted on a jack to support the rear lower control arm
  3. Remove or disconnect the following:

    Electronic Ride Control (ELC) air tube from the shock Two bolts securing the shock to the control arm Trunk trim to gain access to the shock upper mounting nuts. Cover, the two nuts, and the reinforcement from the top of the shock Shock from the vehicle

    0900c152802427e1.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Remove the cover to gain access to the upper shock absorber mounting components-rear suspension


    0900c152802427e2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the lower shock absorber mounting to the knuckle assembly-rear suspension


To install:
Install or connect the following:

Shock, reinforcement, and the two nuts. Tighten the mounting nuts to 15 ft. lbs. (20 Nm). Shock cover Trunk trim Shock-to-control arm bolts and tighten the bolts to 18 ft. lbs. (24 Nm) ELC air tube to the shock. Tire and wheel assembly

Apr 09, 2009 | 2001 Buick LeSabre

1 Answer

2004 dodge stratus SE


This is a dangerous job if you do not have the proper equipment for compressing the spring that is around the rear shock. I do not recomend performing this job without the proper equipment. Unloading the spring without it compressed can cuase injury.

If you have the proper equipment this is how you do it.

REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
  1. Roll back carpeting on top of the rear shock tower to access shock mounting nuts.
  2. Remove plastic cover from the top of the shock assembly.
  3. Remove 2 nuts attaching the shock assembly upper mount/spring seat to the shock tower.
  4. Raise vehicle on jackstands or centered on a frame contact type hoist.
  5. Remove the rear wheel and tire assembly from the vehicle.
  6. Remove two fasteners holding the splash shield to the shock assembly upper mount.
  7. Remove bolt attaching shock absorber to rear knuckle
  8. Remove the shock absorber from the rear knuckle first when removing the shock absorber from vehicle by pushing down on the rear suspension.
  9. Move shock assembly downward and tilt top of shock outward, then remove shock assembly from vehicle through top of wheel opening.

Aug 04, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...