Question about 1995 GMC Suburban

1 Answer

My rear door won t stay open on one side when I load groceries in the back. Ithink it is the brace or hinge. Any solutions for parts or part #?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

GM part number 15048810 door strap

Posted on Nov 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

1 Answer

How to adjust rear doors onhj75 troopy


the door hinges move in or out to adjust that side of the door and the door lock latch moves to adjust that side.. loosen the door hinges just enough to move the door then -tension them to see how you are going. With the door open and the bolts slightly loose it may be possible to move the hinges by placing a long bar on the hinge past the door edge and hitting with a hammer

Jun 26, 2013 | Cars & Trucks

1 Answer

Radio does not go off when key is out of ignition and door is shut


You are on the right track...the problem appears to be on the driver side rear door actuator switch...locate this spring loaded sensor usually on the inside of the door by the hinges...spray it with PB Blastor, or WD 40...(Blastor works better) and move the switch back and forth...this should loosen up the sticking actuator and return your Buick to normalcy...Hope this helps

Jul 03, 2012 | 1998 Buick Century

1 Answer

How do you replace the drivers door hinge?


The hingepin is available in some of the help kits at the parts store. If you are just trying to make the door tight again there is no reason to unbolt the hinge. You just grind or chisel the top shoulder of the pin away and then punch the old pin through the bottom.

Put the new pin through the hinge and bend a shoulder on the new pin. Some may even use a nut with threads.

To install the pin or replace the hinge you should open the door and try to brace the bottom of the door with a bucket or books or anything where you can keep the door from changing position. Once braced, a hinge will just unbolt and you can swap it with the new part. Do one hinge at a time if you have 2 on a door.

Oct 20, 2010 | 2001 Ford Expedition

1 Answer

2002 honda odyssey power sliding door roller replacement. Is this a hard job to do?


Not very difficult if like my '99. Be sure to purchase the correct hinge for "power" door. Here are the steps:
  • Remove rear tail light (2 screws and pull from socket)
  • Remove two screws from rear of hinge cover panel
  • Remove bolt from front of hinge cover panel
  • Open door around one foot and rest the back end on something about the same height
  • Remove the three bolts from the hinge connecting it to the door
  • Loosen slack on cable by unbolting pulley under inside rear panel (tire tool storage on driver side)
  • Slide broken hinge out back of rail
  • Replace new hinge and put all back together
I don't know if there is a simpler way to loosen the slack on the cable, but this is how I did mine.
Hope this helps.

Jul 20, 2010 | 2001 Honda Odyssey

1 Answer

Driver's side mirror won''t stay in the mid-position


Check the hinge on the doorpost,,,its likely that the pin holding the arm that holds mid open position has sheared (look at other door and You will see how it's set up) If it;s broken you can use a small bolt or even a cut off nail to replace it!

Mar 21, 2009 | 2004 Jeep Grand Cherokee

3 Answers

94 jeep cherokee door troubles


from the late 80's to the 90's jeep cherokees have a known problem with there front door hinges. the first time i seen this on a jeep i thought it was a fluke but now owning a 93 cherokee i am goin through the same problem... most of the time its not the door pins (i am not saying this is not what is wrong with yours, but for the most part it is not the pins). on the inside of the sheet metal, where the door hinges are welded onto, tend to rust/wear out and cause up and down play in the top door hinge. the only way to fix it is to take the door off and reweld a new brace or support underneath the sheet metal, and the weld the door back into place... my jeep is goin threw this process right now... but if you dont fix the door soon it will acually rip the top door hinge out of place, allowing the door to almost touch the ground when opened.

Sep 27, 2008 | 1995 Jeep Cherokee

Not finding what you are looking for?
1995 GMC Suburban Logo

Related Topics:

904 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...