Question about 1988 Jeep Grand Wagoneer

Open Question

1988 Jeep Grand Wagoneer NO power to radio

Not the fuse ? What else could it be PLEASE

Posted by on

  • malie5 Apr 18, 2009

    Sorry No it is not pulled out. I got the back window fixed ( It was not rolling down) When we got the Jeep back the Radio would not power on at all. We checked all fuse.

  • yadayada
    yadayada May 11, 2010

    and you have pulled the radio and verified the connector to it does not have 2 12 volt sources with the key on?

×

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1988 JEEP GRAND WAGONEER GAS GAUGE READS OVER FULL

The ground has corroded off the sending unit.You can access this by drilling out the rivits in the access panel under rear seat on drivers side.

Posted on Nov 09, 2008

  • 290 Answers

SOURCE: 1988 Jeep Grand Wagoneer REar Window won't go up

bad window motor or window regulator or both.

Posted on Aug 29, 2009

  • 6982 Answers

SOURCE: engage 4 WD 1987 Jeep Grand Wagoneer

There usually are instructions above the sun visor. To engage, just pull the lever into the gear you want while rolling. (work best that way) use low only for pulling something out of mud etc. try to avoid using on dry pavement as that will wear the transfer case faster. Use N setting if your vehicle needs to be towed. After using if it fails to disengage, usually backing up about twenty feet will fix that.

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing belts on 1988 jeep wagoneer


I'm assuming your question deals with how to route the belt...
There is usually a belt routing diagram near the radiator...

Jun 09, 2011 | 1988 Jeep Grand Wagoneer

1 Answer

I have a 1988 Jeep Grand Wagoneer that seems to be losing oil pressure then dying. I just changed the oil and the levels are fine. Not sure where to start... any ideas?


if this just started when you changed the oil and filter,then it might be the filter,it did it in my 89 jeep so i changed the filter to another brand and my oil pressure came back to normal.so i would recomend and stp or k&n or wix filter.if that doesnt then start looking at the oil pressure sensor and wire lead.you could also use a mechanical oil pressure guage and check it that way to.

Jun 01, 2011 | 1988 Jeep Grand Wagoneer

1 Answer

The hood release latch to my 1988 wagoneer is broke how can i open it?


Take a long flat screw driver and you reach the hood latch under the hood. You might need a flash light to see the latch under there. You have to push a little for it to releese. Thats how I got mine open.

Jun 15, 2010 | 1988 Jeep Grand Wagoneer

1 Answer

1988 wagoneer electrical issue


I believe that your headlightsw are powered by a fusable link, likely connected near the alternator or battery, I't's possible that the wire may have dropped and did not get re-connected when you installed the alternator, or it was weak and failed while you were working.. I don't see why it would cause the aternator to not charge but either it also completes the battery circuit or there is a second wire.

Jun 25, 2009 | 1988 Jeep Grand Wagoneer

1 Answer

Vehicle dies out


It could be either one it could also be the catalytic convertor

Mar 18, 2009 | 1988 Jeep Grand Wagoneer

1 Answer

1988 JEEP GRAND WAGONEER GAS GAUGE READS OVER FULL


The ground has corroded off the sending unit.You can access this by drilling out the rivits in the access panel under rear seat on drivers side.

Sep 30, 2008 | 1988 Jeep Grand Wagoneer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...