Question about Chevrolet S 10

1 Answer

Replaced the U joints on my 2001 Chevy s-10. One of the U-joints had a coupling when I removed it. However, the parts store said there is no call for a U joint with coupling that attaches to the rear

I replaced the U joints on my 2001 Chevy s-10. One of the U-joints had a coupling when I removed it. However, the parts store said there is no call for a U joint with coupling that attaches to the rear Yoke. Any ideas?

Posted by on

  • stb2005 Apr 18, 2009

    yes I am.

  • Richard Scordino May 11, 2010

    What kind of coupling? what does it look like?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Are you talking about the straps that hold the joint to the rear yoke in the third member. ?

hope2help shack

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Makes a funny noise when i go over a speed bump chevy 2001 mal


what sort of noise clunks&bangs could be anything from shock mounting bushes exhaust hanging mounts or suspsion bushes.it would be a good idear 2 have a mechanic put it up on a hoist 2 check it out

Sep 10, 2011 | 2001 Chevrolet Malibu

1 Answer

I must replace the oxygen sensor in my 2001 Chevy Silverado. I found it on the front side of the catalytic conv. but the space is so tight what is the best way to remove and replace this part?


You should be able to remove it with a 7/8" combination wrench. There is also a special socket for O2's that you can purchase or maybe borrow from a parts store.

Sep 01, 2011 | 2001 Chevrolet Silverado 1500

1 Answer

I have a problem removing the bottom ball joints on 2003 chevy trail blazer need step by step please.


remove steering knuckle with wheel hub and bearing attached ,remove lower ball joint flange with a chisel,remove the lower ball joint using a ball joint press you can rent the press from some local auto parts store or purchased from harbor freight for about 60 bucks.

Feb 25, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

How do i replace the ball joint on a 1996 chevy blazer four wheel drive


you need to purchase a pickle fork from a local parts store to remove old ball joint then replace new one using a jack to put pressure on it while you tighten new joint in place.

Dec 06, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

I have a 2wd 2003 chevy s-10 extended cab short box pickup. The rear half of the driveshaft is starting to vibrate. I was told I had to replace the whole driveshaft, but I am finding it very difficult to...


You shouldn't have to replace the whole shaft. Go to auto Zone or Advance Auto Parts and tell them you need the Rear u-joint for the Drive Shaft of that vehicle and they should have it. The replacement process is a little tedious but can be done. Get the Haynes repair Manual on your vehicle, while your there at the Auto parts store, and look up the Drive Shaft. It will tell you how to remove, inspect and if needed replace the U-Joints on your drive shaft. If in fact for some reason, and I have never seen or heard of this, the U-Joints can't be replaced the Manual will tell you. Because they are usually pressed in on the shaft itself some say you have to replace the whole thing but they can normally be removed with a little muscle.

Aug 07, 2010 | 2003 Chevrolet S-10

1 Answer

How to change ball joints on 1994 chevy blazer


Changing the actual ball joints themselves is pretty easy (the replacements just bolt in), however disassembling everything else is very involved, especially if you have a 4x4. Some of the original equipment ball joints are riveted in, so you may need to drill out the rivets to remove the old ball joints. Some models have ball joints that are pressed in. (Your model should not be pressed in. They are either riveted or bolted if they have been replaced already) This is not a job I would recommend to someone who does not know how to do it. You need to disassemble/take tension off the suspension, disassemble the steering knuckles, etc. There are specialized tools you will need as well such as a pickle fork for breaking the knuckle away from the ball joint/A arm, spring compressor or torsion bar removal tool (depending on what your vehicle is equipped with), torque wrench, etc.

If you are set on tackling it anway, do yourself a favor and go to your local auto parts store and pick up a repair manual for your Blazer. It will have the procedure to step you through it, torque specs, and tool part numbers listed in it.

Jan 14, 2010 | 1994 Chevrolet S-10 Blazer

1 Answer

Remove spindle on 86 chevy 4x4


Generally you need a special tool to remove and repress the ball joints. Some auto parts stores have a lowner tool program. You leave a deposit and they lend you the tool.

Sep 20, 2009 | 1986 Chevrolet K1500

3 Answers

2001 chevy S-10 pickup six cylinder unable to remove one plug.


either take the steering shaft off of the either the steering box or from the top.

i have a 99 blazer and i had the same problem, i put the socket on the plug and a stubby open end wrench and slowly pulled it out.

Aug 14, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

How do you remove the heads from a 2001 chevy s-10 p/u?


this would be to long to type out and hard to explain it would be best to buy a haynes book from a parts store they are usally around 15 bucks

May 01, 2009 | 1996 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...