Question about 2002 Dodge Durango

1 Answer

1999 5.2 durango, codes 300,301,308. I've changed rotor, cap, pluges and wires but still get codes after they have been cleared. Any help please!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Try looking at spark from coil. Pull coil wire (hold with well insulated pliers or similar to avoid shock) and hold away from coil. crank it over and observe spark. If 1/4"-1/2" & orange/yellow color, replace it, if about an inch or longer & nice blue color, coil should be o.k. Appears that computer problems are not uncommon on these, so if that doesn't fix it, I would disconnect battery connections, pull computer connections, clean well with contact cleaner, add a little dielectric grease and re-assemble & try. Otherwise you may have to have computer tested by good mechanic. Remember, even though some people don't like going to a dealer, they are the most likely to have run into this the most, and usually know right where to look. Keep us posted, good luck.

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 99 Durango 5.9 rpm goes up and down rep. Crsen wires plugs cap rotor bug still runs really rough


Check to see if all the vacuum hoses are connected to the right source.
Regards
Sir Dana

Apr 27, 2017 | Dodge Cars & Trucks

1 Answer

Po302, 1999 Jeep Cherokee #2 cylinder misfire


Try checking fuel injector.
Try checking compression.
Is the engine running ok, maybe you're getting a bad code, if so you need to find out how to clear it, sorry I can't help you with that. Good luck

Sep 24, 2015 | 1999 Jeep Cherokee

1 Answer

Was idleing at store then shut off and wouldnt fire. Changed crank position sensor,coil,and distributer cap... what could it be there is no spark!! Plz help mom of 3 no car


Possible bad ignition wire from coil to distributor cap. Possible ignition rotor inside distributor cap shorting to ground. Possible no power to ignition coil

May 18, 2015 | 1999 Dodge Durango

1 Answer

My dodge Durango 1999 won't fire up after I put a new distributor cap on and new wire


your rotor may be cracked or try the ignition coil wire. it may be loose

Sep 08, 2012 | 1999 Dodge Durango

2 Answers

What's your problem?I did all these changes to my 1999 Dodge Durango. They are distributor cap, rotor, wires, spark plugs, and pick up coil. My fuel pump is working I also check the alternator and it...


Check that the crank shaft position senser is plugged in and working and not broken this will cause your comp to not send fire to you coil and it won't fire hope this helps you

Oct 12, 2011 | 1999 Dodge Durango

1 Answer

No spark to ignition coil or spark plugs. we have replaced all spark plugs and wires cap and rotor down stream O2 sensor too.


The Cam & Crank Sensor controls whether the coils will give spark to the engine or not if you scan the computer it should give you a code for 1 of these sensors. They are very easy to change and are only around $50.00 each.

Apr 29, 2011 | 1999 Dodge Durango

1 Answer

Mixed up fireing order while installing new plugs, wires, cap & rotor. need diogram


Firing Order 1-8-4-3-6-5-7-2 And here's everything you'd ever want to know about the ol' 360: From http://www.dodgeram.org/tech/gas/specs/5_9v8.htm if this information helps please rate my help

Apr 20, 2009 | 1999 Dodge Durango

2 Answers

99 5.2 durango :pulled codes for multipe missfire cylinder #5-7


Aloha We have just replaced all of what you have replaced, plus water pump, fuel pump, pcv valve and 02 sensor. Took it to mechanic today we had misfire on 1,2,6,7. Mechanic said that the 99 dodge is known for bad computers, he checked ours and works great turns out that it was the coil. Ours was jumping 1/4 inch and had a orange/yellow spark. it is supposed to have a 1 inch spark and be blue. This has solved our problems after 527 dollars later.
Check the coil!

Feb 26, 2009 | 1999 Dodge Durango

2 Answers

Cylinder Layout V8 5.9 L Magnum Dodge


drivers side plugs from front of engine to rear are cylinder numbers 1...3...5...7
passenger side front to rear 2...4...6...8..
fiing order 1..8..4..3..6..5..7..2..

Sep 07, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
2002 Dodge Durango Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...