Question about 2003 Chrysler Concorde

3 Answers

How do I replace a 2003 Chrysler Concord headlight bulb?

Its the passenger side, and there seems to be no way to get to it without dismantling the entire front of the car. I can get to the hi beam bulb but I need to get to the low beam. No room

Posted by on

  • RA Montgomery Apr 18, 2009

    There are definately two seperate bulbs, one for low beam and one for hi beam. I even checked the VIN to be sure it is a 2003. Then I looked at the headlight bulb guide at an auto parts store and it lists different bulbs for hi and low beams. I understand about turning the ring but even if I had room to grab the ring to turn it, there would not be enough distance behing the bulb to clear the bulb much less the plastic connection. Something is going to have to move some direction.

    HELP Rick

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Open hood, remove radiator suport bar that has the hood latch on it. in the center above the grill there are 2 10mm bolts and 3 plastic fasteners with a pin in the center of them, pull pin up and remove fasteners. there are 2 plastic fasteners on each side of center piece i broke them off and replaced the with fasteners with push pin from auto store. remove 10mm and 13mm bolts holding the center support bar and 2 long 7mm bolts holding headlight assembly lift bar up and set on engine. be carefull not to scratch fenters or anything else with th end of bar. there will be just enough room to remove bulb. after you've done it once it takes ten minutes 2nd time. i just did my wifes 2 hrs ago. thanks gary j.

Posted on Feb 01, 2010

  • comhdw Feb 01, 2010

    2 7mm bolts each light assembly, and you have forcefully pull and tilt light assembly to remove bulb. AGAIN WATCH ENDS OF BAR THE WILL SCRATCH FENDERS, WRAP TOWELS AROUND ENDS.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 226 Answers

There is only one bulb to replace as both beams are in the same lamp. There isnt much room to work, but you just turn the plastic ring & pull the unit back then remove the bulb....) You can also remove the entire headlight adjusting assy that is plastic - with the headlamp intact, but that's another story. hope this helps, rick

Posted on Apr 18, 2009

  • Rick Reichlein Apr 19, 2009

    I had the wrong car as I was thinking about the town and country. You are right there are two lamps in the headlamp as well as the side marker light, starting in 02 I think. They sorta look like the 300M or lhs lights - which have 2 bulbs. Mine takes the earlier assembly, which also is almost impossible to get out. I can see from my book that your low beam is not really changeable without removing the lamp or what is behind it.

    I think on the 2000 you have to 1-remove the plastic splash shield enough on the pass side so that you can get to the facia (bumper) plastic plugs that you pop out to to remove it, unsnap enough of those (wider than the headlamp, so that you can roll the facia back far enough to get to the headlamp jackscrews, which you remove so you can remove the light & change the bulb, - which isn't easy. I think you will have to do the same for the 03 as far as i can tell. This is the best I can do as of today for a solution. Rick

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have a 2003 chrysler concorde lx. I replaced the headlight bulbs and it was a pain for something so easy. Yes I had to remove the radiator support bar that the hood latches on. I was unable to remove the headlamp assembly completely and had to squeeze my had in to get out the high beam bulb. There is a hole to the side and just off center that I think they could have centered onto the bulb that would have prevented the necessary of removing the radiator support bar but we all know this is too simply for Chrysler to figure out (sorry I rant) anyway, if there isn't enough room as previously described then you may have the wrong bulb. The straight bulb will not fit, it has to be the bulb with the L shape connector. The outside(not including the turn signal bulb) is low and inside bulb is high 9006 (no letters or other numbers, at least for mine.) Now does any one know how to actually remove the entire headlamp assembly?

Posted on Nov 02, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrysler Sebring 2008 headlight assembly removal


some times headlamp units have a plastic retaining clip on the underside of headlamp, does the headlight move from side to side? try to pull the headlight back from the top of unit then lift up the headlamp unit, if not it could be the headlamp adjusters holding unit in place.

Dec 06, 2013 | 2008 Chrysler Sebring

2 Answers

Bulb replacement for passenger side low beam on 2003 Mazda6


Google "mazda6club" - a very good forum and search "changing headlight bulb. Hope this helps.
Cheers,Peter

Mar 01, 2010 | 2003 Mazda Mazda6

1 Answer

Where is the crankshaft position sensor on a 2003 chrysler concord lxi


Its located on the passenger side of the engine,back side of engine mounted in the back of the block above the flywheel.

Feb 06, 2010 | 2003 Chrysler Concorde

1 Answer

Can you replace the just the bulbs in the 1998


Yes just the bulb.9006 is your low beam and 9005 is your high beam.They will go in from the rear.





















Feb 01, 2010 | 1998 Chrysler Concorde

1 Answer

Left low beam headlight on Chrysler 2003 T&C wont work while engine is on


Ill guarantee you have an electrical short on the left side of the headlight switch,circuit.From here its immpossible for me to go any further.Good Luck.,Get A Wiring diagram.

Apr 18, 2009 | 2003 Chrysler Town & Country

1 Answer

DHOW TO CHANGE OUT HEADLIGHT BULB ON 1996 CHRYSLER CONCORD LXI


For the bulb removal follow these steps.
-Open the hood and look behind the headlamp assembly with the burned out bulb.
-You'll see a black plastic ring about 2 inches in diameter, rotate this a quarter turn.
-Unplug the bulb, gently pulling the clip up to release the bulb.

Feb 05, 2009 | 1996 Chrysler Concorde

1 Answer

2003 Mercury Sable headlight bulb replacement


This problem is now resolved, thanks to a prior post by sableowner.

http://www.fixya.com/cars/t1479995-2001_merc_sable_headlight_replacement

The 2003 Sable has the same headlight assembly and removal/replacement instructions as the 2001 Sable. Once I had this information in hand, bulb replacement was easy.

Jan 10, 2009 | 2003 Mercury Sable

Not finding what you are looking for?
2003 Chrysler Concorde Logo

1,307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...