Question about 2003 GMC Envoy

1 Answer

Is the job just a matter of removing brake cal , then remove rotor ,or is there more to it

Posted by on

  • craig_hobbin Apr 18, 2009

    hi m.hantash , i am not sure just joined and have no answer to question yet

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi how are you my dear ? can you help me pleas . I want to know how i'm use thies sit.my mail is m.hantash2010@yahoo.com

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

How do you remove the front rotors on a 2008 Commander


in the FSM it is
and at alldata.com every day.
or maybe on youtube. ever search there.
is this your first brake job ever?????????
seems yes, as its just a typical setup.

quote
  1. Raise and support the vehicle.
  2. Remove wheel and tire assembly.
  3. Remove the caliper adapter mounting bolts (3) and remove the caliper adapter from the steering knuckle.
  4. Secure caliper anchor assembly to nearby suspension part with a wire. Do not allow brake hose to support caliper weight.
  5. Remove and discard the O-ring (2) securing the disc brake rotor (1) on the hub.
  6. Remove the disc brake rotor from hub/bearing.

Jul 10, 2014 | 2008 Jeep Commander

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Procedure to replace rear rotors


In short, Remove wheels and tires. Remove brake caliper and brake caliper mount. Remove axle. Take nuts off inside axle and remove entire hub. From back side remove bolts holding the rotors to the hubs.... remove rotor and reassemble in reverse. You will need new oil seals.... This is a heavy duty truck and has some big parts and some really large and tight bolts. Not a job for the meek!

Nov 10, 2010 | 2006 Ford Super Duty F 550 Drw

1 Answer

Chrysler 2001 - my brake pads are new, but someone said my rotors need to be changed. look like the Chrysler dealership that did my brake job, did a poor job. I have been having brake issues every...


replacing rotors is not an easy job but its not all that hard either, brake pads and calipers have to be removed, then the rotor, if your husband doesn't feel comfortable doing this i suggest you take it to a garage, they are your brakes after all :)

Feb 05, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

I have a 98 dodge stratus, are the rear breaks rotors or disc?


You do not require a mechanic to do this job. lst remove any wheel front or back. You probably have front disk and drum on the back.
To remove the rotor, you will see two bolts holding brake capalier on the rotor. Remove these and pry the capalier from the rotor. Now you need to remove the pads. Simple to remove, but when replacing you need a 6 inch c clamp to force the pressure mechanism back into the rotor in order to replace the pads. Remove the rotors and have them researfaced any any machine shop. Cost around $10 per rotor. Pick you up some antisizing compound and high temp grease. Follow instructions on the label. Now remove a back wheel, if you do not see a rotor then its a drum. To remove a drum you will need a several tools to replace the drums. Purchase these at Harbor Freight or Sears. Much cheaper at Harbor freight. Now remove the other wheel and repair one wheel at a time, by checking back wsith the wheel that has not been disambled. Before replacing have the drums reserfaced. Now once the job is completed you need to tighten up the wheel by using the special tool which you purchased. Tighten a little at a time AND ONCE THE WHEEL becomes hard to turn back off a turn. Do the same thing to the other wheel. May take you all day to do the job. But it's the way I learned to do a brake job. Hope this is helpful.

Sep 08, 2009 | 1998 Dodge Stratus

1 Answer

How do I change the rotors and brakes on my 1999 hyundai tiburon?


Steps to replace front brake rotors and pads:

Safley jack up vehicle.
support vehicle on safety stands
remove front wheels
Remove 2 bolts holding the caliper to the caliper support.
remove caliper
remove old brake pads
remove 2 bolts holding caliper support to the spindle
remove rotor, might need a good whack with a hammer to loosen rust bond, also might have a locking ring on one lug stud
sand any and all rust from wheel hub
apply a liberal coating of antisiezing compound.
replace rotor and one lug nut to hold rotor steady
replace caliper support
replace new brake pads making sure squeel sensors are on inside upper corner, also make sure to apply caliper grease to caliper slides and pad sliding surfaces push caliper piston back.
replace caliper
replace wheels and torque to specs
lower vehicle
pump pedal
road test listening for any noises.

PS. these are generic instructions that are very basic, performing a brake job is a very precise and careful job. remember this syetem is responcible for stoping your vehicle at 65mph. this is not a job to attemp if you do not have a good grasp of mechanical applications. One mistake could cause you your life or injurt to your persons or someone else. if you are not comfortable undertaking this task please consult a professional.

please feel free to ask any additional questions you might have.

Aug 28, 2009 | Hyundai Motor 1999 Tiburon

1 Answer

R&R rotors and calipers on 2005 Ford 500 to do brake job


use a large c-clamp to bottom out the caliper pistons remove the caliper bolts .slip out the pads and remove the caliper from the disk
hang the caliper from a coathanger wire to avoid damaging the brakeline after replacement of the pads;brake bleeding is not needed Rotors are held on to the axle like a wheel; with bolts

May 29, 2009 | 2006 Ford Five Hundred

Not finding what you are looking for?
2003 GMC Envoy Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...