Question about 2008 Chrysler Aspen

1 Answer

Paint is cipping on my 2008 and their rust already showing in cipped area

Posted by on

  • lefty2larry Apr 17, 2009

    if there is rust already should get the entire hood paint or just the area where pait is chipped

  • lefty2larry Apr 18, 2009

    What do think this should cost think around figure.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 4,369 Answers

If it's on the hood front, it's stone chips from small road debiris flying up and striking the hood, frille, etc,

If it's behind the wheels, install mudflaps and consider a body shop to spray on Gravel Guard over paint.

Posted on Apr 17, 2009

  • gerry bissi Apr 18, 2009

    thanks for the lousy rating. Always glad to provide free info & get a bad rating.



    Entire hood needs to be stripped to the primer and repainted. Too hard to match paint.

  • gerry bissi Apr 19, 2009

    thank you. appreciate that.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Ford expedition has started to hesitate at low speed (20to35).starts and idles fine and runs better at higher speed..


One or more of your cips(coil in plugs) have gone bad. Go have your code check read at autozone. It should tell you which cip is bad

May 02, 2015 | Ford Cars & Trucks

1 Answer

How do I change out coils in a 2003 ford expedition 5.4 V8?


Your truck has what is called coil in plug commonly known as CIPS. They are located on top of the spark plug boot. You have to take out small bolt that holds it onto the sparkplug. Then you can take out spark plugs. The CIPS are expensive (about 85-100 per cip). I ordered mine on the internet for about 10 bucks a piece and the were new. Be advised you may not need to replace all the CIPS. I only had to change 3 out of 8. Have autozone run a code check then you will know exactly which CIP or CIPS are bad. I would change all the plugs if you have over 60,000 miles on them. Additionally after you change the plugs your truck computer will have to "relearn" the firining order. The truck will run rough for about 3-4 restarts then it will run smooth. Getting the plugs changed took me 5 hours. Theres a lot of stuff in your way as you will see once you get started. The back 2 plugs on both sides are a real pain. Good luck !!

Feb 22, 2015 | 2003 Ford Expedition

2 Answers

How can I help clean the rust from the bottom of my ford windstar 2003?


Scrape off the rust, using a wire brush or scrubbing pad. This technique removes small rust. GM MDI
Apply a rust remover, using a steel wool pad or paper towel. Rub the rust remover into the rust.
Wait 10 minutes for the rust remover to work. Most rust removers contain hydrochloric acid, oxalic acid or other strong acids that dissolve rust.
Clean away the rust remover and the rust with paper towels. Dampen a paper towel, and wipe the areas, again.
Paint on a primer with a paint brush. Let the primer dry. The automotive primers offer protection against rust.
Use touch-up paint that is the same color as the Ford Galaxie. Apply it to all areas that are missing paint. Let the paint dry, before driving the car.

Sep 15, 2014 | Cars & Trucks

1 Answer

# 5 cylinder wont fire, i dont know which cylinder is #5. 2000 ford expidition


looking at the engine from the front. #5 will be the first cylinder nearest to the radiator on the drivers side. by the way its probably the cips(coil in plug) thats bad. once your replace the cips the computer has to relearn the firing sequence. it will take about 3-5 restarts before this will happen. i just did this to 3 cips this past january. easy fix.

Apr 20, 2010 | 2000 Ford Expedition

1 Answer

What has to be taken off to change all 8 coils on 2000 ford expedition


actually nothing. what ford has are called "cips" coil in plug. i just changed my spark plugs out. the spark plug is covered by the "cip". the back 2 near the firewall on both side are a royal pain. forgot to say that each cip is held into place by one bolt (i think its a 10mm bolt). this job will take about 4-6 hours. a faster technique is to unbolt fuel rail and gently pry up the injectors this willl give you more work space. i am willing to bet your plugs are bad and not the "cips". if you are going to change the cip then do the plugs also. the cips run for about 60 to 80 bucks a pop.

Feb 07, 2010 | 2000 Ford Expedition

1 Answer

I have a missfire on #7 cylinder of my 2003 Ford Expedition (5.4L), the OEM code "P0357" -Ign Coil G Primary secondary Ckt shows on my code reader, any suggestions?


first before you waste any money buying a new cip (coil in plug) first just change the spark plug. its on the bottom of the cip. if its bad, i am willing to bet the rest are needing changed out. a royal pain in the **** to change. the easiest way is to unbolt you fuel rail and pop up the fuel injectors. this allows you room to get your sockets in and around the spark plugs (especially the back 2 on each side nearest the firewall. a good 4 to 6 hour job. take your time its really not that hard but time consuming.

Jan 21, 2010 | 2000 Ford Expedition

1 Answer

Where is the sparkplugs? on a 2000 ford expedtion


under the "cip" coil in plug. cip sets on top of plug. each plug has its own cip.

Jun 26, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...