Question about 2004 Mazda 6

1 Answer

I need to replace my air intake hose is this something i can do myself? Or should I take it to a proffesional?

Posted by on

  • Anonymous Apr 21, 2009

    Yes I do I looked it up online but I have no idea How to replace it.

    I took it to the mazda dealer and they said its 160.00 to replace it which seems to me like that really expensive.

  • yadayada
    yadayada May 11, 2010

    do u know what an air intake hose is??


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

No DIY, look carefully and get the right replacement.
My experience with Mazda is that the original part is best.

But if you have no car experience stay away from any jobs.
The thing is can stall dangerously inconveniantly where you don't like it. Then better wash your car.

Then there is the insurance clause if they prove it was your unqualified hand leading to something.

Posted on Apr 17, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What causes air hose collapses and gets pinched off of 2002 mountaineer. around intake carb area

Collapsed hose indicate the pressure on one side is much lower than the other, in this case the intake or suction side is very strong and since the air its pulling into the engine is not sufficient i.e. both sides are not equal, the hose collapses. Most likely you have an air restriction in the hose someplace, could be a really badly clogged air filter, or an obstruction in the air intake at the front of the vehicle where the air intake scoop is. Check that line carefully you'll probably find something in there someplace.

Aug 12, 2014 | 2002 Mercury Mountaineer

1 Answer

States evaporated hose or something, not sure, someone told me that they heard air behind the intake

Then I'd suggest starting your vehicle and checking for any vacuum leaks around your intake and replace any damaged hoses or reinstall them if any have came loose.

Mar 03, 2011 | 2001 Kia Sephia

2 Answers

I cant find ant information on how to find/locate my IAT sensor in a 96' Ford Explorer 4x4 4.0.. I want to try to fix it myself & cant find any information so any help I can get @ all would be greatly...

the intake air temp sensor is in the air snorkel in between the throttle body and the air box. There will be a two wire connector connected to it.

Dec 10, 2010 | Ford Explorer Cars & Trucks

1 Answer

Spark plug replacement.

remove air intake and hoses and as much stuff as possible but not so much as you forget

Aug 13, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Air intake tube?

This sounds silly but try using a piece of garden hose (or any other hose) held to your ear, using the free end as a probe. You will be able to pinpoint the source of the hissing noise and see what needs to be fixed.

Jul 09, 2009 | 2003 Mazda MPV

1 Answer

How to change air filters on 2007 Mercedes C230 Sport

I have '05, both should be similar:
1.Cabin air filter is located above battery on right side against firewall.
Release three latches, remove filter housing, slide old filter out (housing is flexible), insert new
one, reinstall housing.
2.Engine air filter is on the left side of the block (follow intake hose). Cover is retained with six screws
(six point star shape,I belive called Torox, bit/scredriver size 25). Loosen screws (don' t pull all the
way out of the cover) lift cover , and remove old filter. Insert new one, reinstall cover. DO NOT
OVERTORQUE SCREWS! Screw holes in plastic filter housing strip very easily.
Note: Intake hose is very flimsy, one on my car came apart and had to be replaced.

Mar 25, 2009 | 2007 Mercedes-Benz C230 Sedan

1 Answer

1995 Mercury Villager Coolant crossover tube leaking

not likely. You may have to remove the upper intake manifold for access.

go to site for picture of heater hose diagram

Oct 19, 2008 | 1995 Mercury Villager

2 Answers

2003 hyundia accent 1.6

The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles this sensor is combined wit the ATS sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly.
This sensor is located in the air intake plenum assembly. It is combined with the IAT sensor.
The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles it is combined with the IAT sensor.

Oct 08, 2008 | 2000 Hyundai Accent

2 Answers

1997 Chevy Cavalier Z24 2.4l

did you check the gauge that could be bad and did you check the thermostat thaat could need replacing

Aug 02, 2008 | 1994 Chevrolet Beretta

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides