Question about BMW 330

1 Answer

Can't find the socket to re-set service lights

Where is the diagnostic port to re.set the service lights on a 2001 BMW C330

Posted by on

  • yadayada
    yadayada May 11, 2010

    what lights?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Press teh left knob on your clock for 5 second with the key in zero stand if you see the display change thold the knob en turn the key in the 1 stand then you can reset by pushing the knob several times. he will reste to 25000 km good luck

Posted on Apr 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Looking for the diagnostic plug location on a 1993 525 it


SORRY, FOR 1993 BMW, THERE IS NO PLUG FOR DIAGNOSTIC TOOL,
or you can ask the 24 hrs live technical support http://www.diyobd2.fr/ they will like to help you, good luck

Sep 15, 2013 | BMW Cars & Trucks

1 Answer

2001 bmw x5 , it is starting to get a slugest start anytime it starts , but after warmed up opk ,and had check engine light come on same time


Hello
When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

Oct 23, 2012 | 2001 BMW 5 Series

1 Answer

BMW 2001 X5 has intermittent ABS light illuminating. I have changed brakes and brake sensors. The service people are unable to tell me what the problem is via diagnostic computer. What should I be...


BMW MODELS AFFECTED: All with ABS

FAULT: ABS warning light comes on intermittently. Normal troubleshooting procedures find no defect.

Possible Cause: If car has recently had two new tires, or snow tires put on. Sometimes when the car is driven over 50 MPH.

Solution: Check all four tires on the car, make sure they are the same brand, style, and size. Check if
any of the new tires have substantially more tread than the rest. These differences may cause enough
variance in rolling diameters to confuse the ABS control unit, which in turn, gives a false signal to the ABS
warning light.

If that is not the issue, it is most likely the ABS control module failing.

Feb 16, 2010 | 2001 BMW 5 Series

1 Answer

Location of fuel filter on 2001 325 ci


It's located underneath the car, not in the engine compartment, right next to the fuel pump. It's on the driver's side, right behind the front tire underneath a little panel that unscrews w/ a 1/8mm socket. Make sure you get the right filter. Some have one port (opening) in one port out, others have two. My '02 was built in August of '02 and so it has the '03 setup (2 port). Good luck. Don't smoke or use a plugged in light to look at it - go flashlight.
thanks!!!!1

Oct 14, 2009 | 2001 BMW 325

1 Answer

My bmw z3 service engine light is on and the codes show P1899 and P1898. can you help


Error codes not in service manual. presumme dealers can assist you with a pnhonecall for error codes.

BMW SERVICE RESET

Take a small wire, paperclip, or elect wire and bend like a horseshoe. No light or equipment necessary Open the diagnostic data port, the one were the little pacman centre is located. Turn the ignition to position 2, don’t start. Connect pin7 always first and then pin 19. Hold for 4 seconds. Remove wire and settings will be reset. Warning if you hold the wire longer than 10 seconds you may reset inspection intervals 1 and 2.

I’ve done this twice and it definitely work on my E36

Aug 12, 2009 | 1998 BMW Z3 Roadster

1 Answer

How to switch of the service light


Locate diagnostic socket (it's in engine area). Take a piece of wire and short pin numbered 7 to the chasis ground. Turn on ignition key and wait for about 5 seconds. Oil service indicator lamps should go off and 5 green sectors should light up. Swich off ignition, remove jump wire from diagnostic socket.

Sep 22, 2008 | 1996 BMW 318

2 Answers

Oil service light


BMW SERVICE RESET Take a small wire, paperclip, or elect wire and bend like a horseshoe. No light or equipment necessary Open the diagnostic data port, the one were the little pacman centre is located. Turn the ignition to position 2, don?t start. Connect pin 7 always first and then pin 19. Hold for 4 seconds. Remove wire and settings will be reset. Warning if you hold the wire longer than 10 seconds you may reset inspection intervals 1 and 2. I?ve done this twice and it definitely work on my E36

Jul 28, 2008 | 1996 BMW 318

2 Answers

BMW 318i Service Light


BMW SERVICE RESET Take a small wire, paperclip, or elect wire and bend like a horseshoe. No light or equipment necessary Open the diagnostic data port, the one were the little pacman centre is located. Turn the ignition to position 2, don?t start. Connect pin7 always first and then pin 19. Hold for 4 seconds. Remove wire and settings will be reset. Warning if you hold the wire longer than 10 seconds you may reset inspection intervals 1 and 2. I?ve done this twice and it definitely work on my E36

Jul 19, 2008 | 1996 BMW 318

2 Answers

Turning of oil service light on OBD II


My recommendation is definitely in the certified sevis because if you make a wrong conection wires can spoil the main computer

Jun 25, 2008 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...