Question about 1998 Dodge Ram 1500 4WD

1 Answer

How do I change the drivers side u-joint in my 98 ram 1500 5.9l?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 22,326 Answers

Remove the suspension and hub

Posted on May 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cv joint on 98 vr4 galant wont come off


Use a prybar to remove the CV joint, place against hosing and gently pry to release CV.
This is assuming you have un bolted the necessary front end parts prior to removing the CV joint.

Jan 21, 2013 | Mitsubishi Cars & Trucks

1 Answer

Diagram location for a flasher box for a 1999 jeep cherokee


The relay is above the fuse box accessed on the drivers side above the drivers feet. The relay is in the third receptacle from the left on top of the block. A relay costa from $17 up. if your handy with a solder iron when you get the relay out pop the cover off with a small screwdriver. get a magnifying glass and check the solder joints. Usually they crack from the heat stress. Just resolder joints if you find one cracked. and you should be ready to go. If no joints are cracked then its time for a new relay. I just replaced one on a 98 ram pickup owner said just replace it. so i did.

Dec 30, 2011 | 1999 Jeep Cherokee 4WD

1 Answer

What tools other than sockets and rinches will i need to change driver side cv joint on my 98 ford escort se no abs single ohc


There is a CV Joint pulling tool you will need. and make sure you have "deep well" sockets

May 23, 2011 | 1998 Ford Escort

1 Answer

How do you change a front axle u-joint on a 2006 3500 dodge ram


you will have to change both sides to start with. I'm doing this on a 1996 ram 1500. first, put the truck on 2 wheel drive or neutral for traction, raise vehicle, i got a lift it's easy, remove both wheels, calipers and rotors. unlock the driveshaft nut (cotter pin) and unbolt that nut. on the inside of the hub, first mark the relation on one side between the yoke and the shaft, then, there is 3 bolts holding the hub in, remove them. next, more cotter pins, upper and lower ball joint and tie-rod end need to come out, so, unscew the tie-rod end first and seperate it with ball joint seperator. do the same for the upper and lower ball joints. seperate the spindle and the axel should come out. the rest is standard procedure to change a ball joint.
let me know if it's enough info or if you want more please.

Jan 04, 2011 | 2008 Dodge Ram Pickup 3500

1 Answer

98 dodge ram 360 firing order. #1 cylinder location


Number 1 is on the drivers side on the front. The cylinders are arranged 1-3-5-7 down the drivers side and 2-4-6-8 down the passengers side. The firing order is 1-8-4-3-6-5-7-2.

May 25, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

98 dodge ram 1500 rear axle, setting the backlash


there are adjusters on each side of carrier. do most of adjusting from driver side.need about 8 thou of backlash

Jul 27, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Dodge Ram popping noise front left (drivers side) suspension


My father had this problem on a car years ago and I have see others have it also . The poping noise is often for a ball joint and then the wheel just falls off. Have the ball joints inspected for excessive wear 

Dec 15, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...