Question about Toyota Pickup

1 Answer

Replaced sending unit no power to the sending unit but juice to the fuse and relay

I am not getting power to the fuel pump. There is power to the fuse and relay switch but none to the sending unit.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 103 Answers

Is there power coming out of the relay going to the sending unit?

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is ecm on 95 gmc jimmy


The ECM on the jimmy, is located on the passenger side fender well by the overflow tank. But before replace the ECM, inspect the fuel pump and fuel pump relay. The ECM sends power to the fuel pump relay and if the relay has gone bad will cause the fuse to blow which will kill the the power to the ECM, in turn kill the electrical power to the ignition system.

Start by removing the fuel pump relay and swap it with another relay and see if the fuse will blow again, if is does. Disconnect the fuel sending unit wire harness at the frame and see if the fuse blows again, if the fuse stays good. Chances are your fuel pump has gone bad or the fuel filter is dirty/clogged causing your fuel pump to draw more amp and will need to be replaced or the wire harness from the frame to the sending unit has a short which is common on older Jimmy's.

Here is a link to the electrical harness throughout the Jimmy.
http://www.compnine.com/index.php?t=...lid=6872&uid=1

Mar 06, 2014 | 1988 Mazda B2200

2 Answers

Electrical prblem


There would be a fuel pump fuse, either under dash or under hood. Check that fuse, use the test light to see if fuse has power. If not, then it might be a fusible link or maxi-fuse that feeds the fuse panel. If fuse has power with key on, pull the relay, and use the test light and probe relay terminals, key off. One terminal should be hot at all times. If not, check for power loss between battery and relay terminal-possibly a maxi-fuse or fuse link.
If relay does have power to terminal, quickly check other terminals while someone turns key to on-for about 2 seconds, another terminal should show power-this would be signal from computer to turn the relay on to prime the lines and fuel rail. If you have that, plug relay in and cycle key. Does relay click? If yes, relay is working and problem may be at fuel pump connector. If relay is not working, but you have power to it, and the short signal from computer is there, then check the relay's coil side ground. Computer signals the coil side and the signal goes to ground from relay coil side.
Pull the relay and use a jumper wire from relay's hot terminal to fuel pump terminal-the wire to pump from the relay. If pump comes on, the problem is right there at the relay-either no signal from computer or the relay coil's ground is lost. If pump does not come on, again check connector at pump-that or the wire to pump[ has a problem.

May 12, 2013 | 2001 GMC Savana

2 Answers

My 1999 Kia Sportage won't start. I checked the fuel pump while the key is on the ignition and I get the impression that it is not getting any juice. Fuel pump fuse is OK. Both cam and crank se


Well for starters, you need to diagnose the problem before replacing anymore parts. I say this because you mention both the fuel pump and sensors dealing with the ignition system which are 2 separate main things. Basically it takes 2 things to make an engine start, fuel and spark at the spark plugs. You need to narrow down what is missing because it seems since you replaced sensors dealing with spark and then you mention the other need fuel. I'm not sure as to where to start to help until whatever is missing is diagnosed and then find the cause of the loss. There are a couple of things you can check. Below is a picture of the relay box in the engine compartment. With the help of somebody put a finger touching both the fuel pump relay and the EGI main relay. While touching them have somebody turn the key to the "on" position (no need to try and start). When the key is turned on you should feel a "click" inside both of those relays. The fuel pump relay will click for about 3 seconds and the click again to shut off. The EGI main relay should stay on. If both seem to be fine you need to make sure of the fuel pump gettting "juice" and for power to the ignition system like the coils. You can get to the power/juice wire at the fuel pump pretty easy. You can access the connection at the fuel pump by lifting the lower part of the rear seat. Once the seat is lifted you should be able to see a part in the carpet that is cut to be able to lift the carpet up and access the plate covering the access to the fuel pump and/or the top of the fuel tank. Using a test light, check the green and yellow wires at the fuel pump. You should have power at those wire when turn the engine over or if the key is just turned to the on position you should have power there for about 3 seconds. To begin checking for spark or power to the ignition system you need to make sure you are getting power to the ignition coils. The red and white wires at the coils are your power wires. Check those. Also you can check the power at the fuel injectors. When the key is turned on or when trying to start, you should have power to the green wire at each of the fuel injectors. You should have constant power/juice at each of the fuel injectors. This is where I would start to narrow down the loss. Start here with these tests and let me know how the tests come out by replying/commenting here or you can email me directly at csautomotivecars@att.net ith what you have found out. Once the first tests are done and I know what the results are, we can go to the next step with a couple of other tests to figue the problem out. If one of the relays don't "click" then you have a possible bad relay. The EGI main relay is a common thing to go as well as the fuel pump relay. Don't mind helping and there is no cost to you for it but I don't want to tell you to start replacing parts until the problem is located. Hope this helps get you started.


4_24_2012_10_38_55_am.jpg

Apr 23, 2012 | 1999 Kia Sportage

1 Answer

Replaced fuel pump truck ran fine then sendingunit quit working . i was checking fuses by pulling them one at a time now fuel pump will not work checked to see if it had power to pump .could not get power


The oil pressure send ing unit is a back up power supply for the fuel pump moter its a safty thing. Check fuse # 9 When the fuel pump is replaced the wires need to be cut and spliced because they had a problem with the wires giing to the pump over heating so the new pump has a differant connector the old one will not fit into it check the 4 wire connection splice I dought its the relay thats in the glove box thats what the back up is all about through the oil pressure unit the vehicle would still get power to the fuel pump even if the relay was bad I have a wireing schematic of a 2000 if you want it give my an Email address and i will send it to you pier-j

Jun 07, 2011 | 2002 Chevrolet Blazer

2 Answers

O sound from fuel pump


Always check the fuses first, because they are so easy. Also, the relay may be at fault. You should hear this click when you replace the fuse for the pump with the car ON, but not started. If no fuse problems, then check for power @ the connection for the pump after removel of the electrical connector. If you have power here, then it is a bad pump, or connection.
Good Luck!

Feb 14, 2010 | 2003 Pontiac Montana

6 Answers

No power to fuel pump


when u checked this u do realize the fuel pump only has 12 volts for 1 second then the computer turns it off unless the engine is started? let me know.

Dec 03, 2009 | 1997 Dodge Ram 1500 Club Cab

1 Answer

New relay an new fuel pump no fire goin to fuel pump


Check fuel pump fuse, remember fuse send power to relay and relay sends power to pump, Check power wires to pump and make sure FUEL PUMP FUSE IS GOOD if not replace and take care of this problem. Good luck and thanks for using FIX YA.

Mar 25, 2009 | 1990 Ford F150

4 Answers

Chevy s10 pickup fuel pump does not work


i have a 98 chevy s10 zr2 and we changed the fuel pump and aint gettin no power to the fuel pump checked the fuses and relay under the hood no power and the gauges inside are not working other than lightin up.are there another fuse link some where

Mar 18, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...