Question about 1997 Chevrolet Venture

1 Answer

Is it difficult to remove dash to replace burnt out bulbs behind heating controls on 2003 chevy venture?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Nowdays a lot of the newer cars just have clips so it should pull out for the most part then you might have to use a philips to remove some screws from the control unit in order to get at the bulbs

Posted on May 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My light on my speedometer doesn't work. I have a 2004 chevy venture, which fuse controls that or could it be a bulb that's out


If all the rest of the lights in the dash are working, then it is the bulb. Just pull out the dash and replace bulb

Mar 10, 2015 | 2004 Chevrolet Venture

1 Answer

How do I replace the bulb behind my fan speed switch for a 2003 Tacoma?


You must remove the dash control to access the bulb.

Feb 26, 2015 | 2003 Toyota Tacoma

1 Answer

No tail lights and only middle and passenger brake light works on my 2001 chevy venture


The tail light assembly on this vehicle is a poor fit and moisture softer invades the bulb assembly when it rains. Remove the tail light assembly and replace any bulbs that have shorted out. You may need to replace the assembly.

Feb 04, 2014 | 2001 Chevrolet Venture

1 Answer

Lights out on 2003 chevy impala heat and air switch


You will need to pull the control head out and replace the tiny bulbs that are hard wiried to the circuit borad inside, this requires very good skills in solder repair. The light bulbs are available from Radio Shack, the part number is 7219

Feb 23, 2012 | 2003 Chevrolet Impala

1 Answer

Where is the powertrain control module located in a 2003 chevy venture van? Thank you


It is located in the air cleaner.Take off the air filter cover/air boot.\Then there are 2 8mm headed bolts on the top of the air cleaner.remove the two bolts and pull off the cover.The pcm is located behind there.

Aug 18, 2011 | 2003 Chevrolet Venture Passanger

1 Answer

I have a 2003 chevrolet Impala. The dash light in the climate control section is burnt out. How do you replace the bulb(s).


unfortunately the bulb is not replaceable, and you will have to replace the entire unit.

Jan 07, 2011 | 2003 Chevrolet Impala

1 Answer

My Chevy Venture 2003 door chime on drivers side chimes without key in ignition with door open. Before this happened my dash lights acted funny and then went out. When I shut off the van and opened the...


Sometimes the ignition key does not "deactivate" when removing the key...try wiggling the washer behind where the key goes...sometimes this sticks...:)

Dec 08, 2010 | Chevrolet Venture Cars & Trucks

1 Answer

How do you replace a burnt out bulb behind heater controls?


Remove the dash assembly where the heater controls are and replace the light system that is burnt out

Dec 03, 2009 | Dodge Caravan Cars & Trucks

1 Answer

NO HEAT AT IDLE


Replace you cabin air filter, it's probably plugged just got mine replaced and it works great now.

Jan 20, 2009 | 2003 Chevrolet Venture Passanger

2 Answers

Thermostat in a 2003 chevy venture van


the bottom boult is hard but can be done need to use a 10 or 12 stubby wrench and take a pry bar and lighty pry heat shild away to get bottom bolt dont need to take it out all the way just loosen and slide down

Aug 08, 2008 | 2003 Chevrolet Venture Passanger

Not finding what you are looking for?
1997 Chevrolet Venture Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...