Question about Mazda Protege

2 Answers

Abs stays on - Protege Mazda Cars & Trucks

Posted by on

  • bigotyme Apr 17, 2009

    Ok thanks ...I will get back to you and let you known what happen.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

What exactly do you mean it stays on.... the light stays on ?


Robert

Posted on Apr 18, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 854 Answers

1. fill brake master cylinder with brake fluid it may not look like it needs it but the sensor is at the top of the resivior.
2. If abs and brake light staying on then there is probably a malfunction detected by the control unit. Codes can be retrieved using the following method. Under the hood to the rear of the left front strut tower you will see a small 2"x3" gray box that should say diagnosis on it. Open the top and you will see a pattern of two places where a connector might fit. . The connector will look lilke this [ ][ ] [ ][ ]
[ ][ ][ ][ ][ ][ ][ ]
[ ][x][ ][ ][ ][ ]

[ ][ ][ ][ ][ ][ ]
[ ][ ] [ ][ ]
Get a small jumper wire and a paper clip and ground the pin that has the 'x' in it. Now turn the ignition key to run and watch the abs warning light. It will come on for 3 seconds and then out for two seconds. It will then flash you a two digit failure code. Long flash(s) of 1.2 seconds followed by short flash(s) of .4 seconds. The long flashes are the first digit and short flashes are second digit (ie 4 long flashes followed by 2 short flashes would be a code 42. Once one code is output the light will go off for 4 seconds and then either flash you any other codes or repeat if there is only one. Try this and then post with the code you get. Would post what they all mean but there are 31 different codes and I am tired of typing already. Good luck and make sure only ground the specified pin. Can cause damage to electricals if grounding wrong one.

hope this helps

Posted on Apr 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does my ABS light stays on and sometimes i get a vibration in the brake petal causing my 2002 Cadillac escalade not wanting to stop?


Sounds like a fault with the Antilock Braking System. The vibration in the pedal is the ABS working. With your foot on the brake pedal, it releases and re-applies the brakes to stop a skid from the wheels locking up. You need professional service for brakes.

Seems to be a known issue on all Cadillac and requires the ABS module to be replaced.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille Cadillac DeVille ABS Light Due to ABS Control Module Failure. This is a verified problem based on 126 reports. Learn more about this problem, when it occurs ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville STS Traction control and ABS lights stay on dash. This is due to ecbtm Module gone bad. replace Module and this should fix the problem. You can go by the VIN and ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille DTS ABS Light Due to Control Module Failure on Cadillac DeVille DTS. The anti-lock ... ABS and Traction control light stays on. ... abs light to abs control stay on.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville SLS ABS Light Due to Control Module Failure on Cadillac Seville SLS. The anti-lock brake ... SLS135,000Jumsee. Abs and traction lights stay on when started.

Jan 12, 2016 | Cadillac Cars & Trucks

1 Answer

Abs and beak light stays on


ABS SYSTEM IS MALFUNCTIONING or CHANGE THE FUSE under the hood if the fuse is blown both lights will activate. If the ABS light stays on then pull the ABS fuse

Oct 24, 2013 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

95 saab 9000 abs light stays on


could be bad sensors replace,there are in hub bearings.

Mar 02, 2013 | Cars & Trucks

2 Answers

Honda civic abs stays on


Just pull the abs fuse ,anything that disables the motor will
leave you with "old fashioned" brakes. No abs but base
brakes will be fine .ABS light will stay on .

Feb 16, 2013 | 2012 Honda Civic DX Sedan 1.8L 4-cyl....

1 Answer

Abs light stays on, after changing brakes, 1997 caddy deville


ABS light comes on with ignition then should go off when you start the car.
If abs sensor does not turn off after disconnecting the battery, then there is a real problem, a faulty sensor or ABS malfunctioning.

Jun 11, 2012 | Volkswagen Caddy Cars & Trucks

1 Answer

ABS light stays on - can you unsolder relay in ECM with common iron.


ABS light on did they check codes ? The light staying on an no codes is usually a insturment cluster problem not the EBCM - electronic brake control module . No relay in side the module , a transistor or diver as they call them . This transistor will supply a ground on a electrical circuit from the brake lamp driver module ,when it does this the brake lamp driver module ground a electrical circuit for the ABS light . If anything is bad causing the ABS light to stay on it would be the brake lamp driver module . Your best bet ,take it to a GM service dept.

Aug 05, 2017 | 1999 Pontiac Bonneville

1 Answer

Abs light stays on


Possibly a ground for the abs wiring or a sensor is gone in your brakes.
Most likely a wire torn to your abs sensor

Jan 05, 2012 | 1994 Honda Accord

2 Answers

My abs light stays on on my ford focus


when the ABS light stays on it means there is a fault present in the ABS system and the ABS has been disabled, as long as the light is on u just have regular brakes with no ABS, there are many thinbgs that can turn the light on, most common is one of the wheel speed sensors is defective, since these sensors are about $75-100 each and there are 4 of them guessing is a poor idea, so what u need to do is have the ABS systwem tested, there will be a fault code present to help narrow down the defective part or wiring.

Dec 28, 2009 | 2004 Ford Focus

1 Answer

My ABS light stays on what could this be ?


scan abs module and you will find a code 265..the internal relay has failed will need to replace abs module

Dec 27, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Shows ABS fault on dash and ABS light stays on


Check your abs connectors they might have pulled a wire loose

Nov 11, 2008 | 2004 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...