Question about 1994 Honda Civic

1 Answer

Turn signals and hazards won't work

My turn signals and hazards wont work! i replaced the relay twice and checked all the fuses but still nothing!!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Was there any electrical issues other than this? Was there anything done to replace an electrical part or a stereo, gps, or other devices added to your car? Was a wire spliced or any wires cut that your aware of? Maybe the tail lights wiring have been altered to add as a source for connecting a trailer wiring harness? Try removing the **** shell around the ignition and carefully inspect the wiring in and around for loose, faulty or wires that may have been cut. Youll want to disconnect the battery first so you wont accidently create a short or spark that could create a bigger problem! Inspect your turn signal switch while you have the **** shell removed and make sure the parts are all intact and functioning, as well as the hazard switch. Could also be that theres simply a wire or wiring harness that had been disconnected while someone was working on another area related to the area where the problem is occuring. Hope this info is helpful or at least leads you in the direction of locating the problem.

Posted on Apr 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

My turn signals stopped working as well as the hazard lights. I replaced the fuse under the hood for the hazard lights and now they work but still nothing for the turn signals. I checked every normal (10,...


You only replace the one flasher you need to replace the turn signal one to its also located under the dash if you did that already replace your turn signal switch

Jun 27, 2011 | 2000 Chrysler Town & Country

2 Answers

How to check the turn signal relay ? and where is it ? and how to replace it.


See picture below of drivers side fuse panel and run these tests at the relay holder pins:

E is ground...measure resistance between it and ground (someplace else on the car) to make sure it is 0 ohms or at least very close to it.

B terminal should be 12 volts, if not, you might have a blown fuse (#1), or a faulty hazard switch.

Short B and L and flip hazard switch. If nothing happens, bad #20 fuse, bulbs, poor ground, bad hazard switch, or cut wire.

With B and L still shorted, flip turn signal either direction. If nothing happens, you have bad signal switch.

If all tests pass, the relay is bad.





psawall_1.jpg

Dec 01, 2010 | 1992 Honda Accord

2 Answers

Have 95 mitsu..Diamante, the hazards flash but my turn signals wont. I have replaced all fuses, does anyone have a solution?


Did you check to make sure all the bulbs are working? on some cars the flasher for the hazards work even when some bulbs are out but the turn signals will not. If you have blown bulbs replace them and it should work if not then you have one of a few cars that have two relays for the signals, one for hazards and one for turns signals.

Oct 28, 2010 | 1995 Mitsubishi Diamante

1 Answer

My blinkers stopped working. At first I had to manually "blink" them, today they wont turn on. The hazards work fine. Its a 1992 roadmaster estate wagon.


Your fuse is blown or the flasher relay is defective or both. Check the fuse first and replace as nexessary. Note that this vehicle has 2 flasher relays, one for the turn signals and one for the hazard lights. The turn signal flasher relay is located on the driver's side, under the dash above the kick panel, mounted in the top of the fuse panel. The hazard relay is located same place on the bottom of the fuse panel so do not get them mixed up.

Oct 05, 2010 | 1992 Buick Roadmaster

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Turn signals and hazards dont turn on


The turn signals run through the hazard switch, I have replaced hazard switches for this problem.

Apr 22, 2009 | 1996 Honda Accord

1 Answer

Turn signals wont work but flashers do


Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Aug 31, 2008 | 1998 Dodge Dakota

Not finding what you are looking for?
1994 Honda Civic Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...