Question about 2006 Ford Taurus

1 Answer

How can i reprogram a new ignition switch cylinder?

I purchased a 2007 Ford Taurus & there was no ignition switch. I installed a new ignition switch, the car didnt start, the theft light is still on. Is there any way to program without taking the car to the dealer? and how can i reprogram it? thank you for your help. Leo.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 43 Answers

Well sorry to tell you if you have a PATS key for your ignition you will have to take it to your Ford dealer to get your keys programmed. My advise to you is just to get 1 key programmed then tape it to your steering column and get regular keys from the hardware store cut to fit your ignition that way if you misplace it it only costs you $2.00 to get a new 1 made.

Posted on Apr 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reprogram the ecu after replacing ignition due to breaking key off in it


take the new key and the car to a service dealer and have the immobiliser program the new key.

Mar 04, 2015 | 2007 Ford Taurus

1 Answer

I just replace the Ignition switch in a 2002 ford Taurus.How can reprogram the new Keys


If your keys have a chip in them key smith or dealer can do this go to YouTube and lookup key programming for your car.goodluck

Nov 02, 2013 | 2002 Ford Taurus

1 Answer

If i remove and clean ignition switch do i need to reprogram to pats


I am not sure, but to clean it, you don't have to remove it, use some cleaning spray and compressed air

Mar 26, 2013 | 1999 Ford Expedition

1 Answer

I have a 98 Chevy Malibu Ls and the ignition won't


Inspect the old ignition cycle which is out.Is there any problem noticed of Ignition cylinder getting worn out.
Because when issue of ignition not turning off,its faulty ignition lock cylinder or faulty ignition switch.I suggest re-inspect the new ignition cylinder.
For more help,click the help link mentioned below:----

Ignition Switch Will Not Turn Off?
http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

2007 chevy cobalt will start but not stay running


problem in theft security system it has to be reprogrammed to new key new ignition switch key lock system. dealership fix need diagnostic eqquipment to reprogram new ignition key and ignition switch lock cylinder to the immobilizer control module and ECM.

Jan 26, 2013 | 2007 Chevrolet Cobalt Coupe

1 Answer

Kexus ignition switch replace


To troubleshoot these issue, for ignition switch replacing procedure:---
Click the link below:---


IGNITION SWITCH REPLACING

It depends on vehicle to vehicle. But it's not very difficult on mot of cars to replace ignition switch. Basic theory of replacing ignition switch is same for all car models. -----

To replace ignition switch on your vehicle, I suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.

-------------

Click the link below: ------

----------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-----------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

---------

These will help.

Thanks.

Dec 06, 2012 | 1993 Lexus Es 300

2 Answers

Car still running after take key out . cheked barrel thats ok don't know if it's relay problem


I think you have a bad ignition switch, not the ignition lock cylinder. they are 2 different things.

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.

Nov 21, 2009 | 1996 Ford Taurus

1 Answer

How to install ignition switch cylinder on ford taurus se 2006


Very easy! Right below the ignition lock cylinder on the steering column shroud (bottom) there will be and access hole, you simply turn the switch to the run (not start) position and with a suitible tool push on the release pin while pulling out the cylinder. replacement will require the clinder to be in the run position while being inserted, then to off position and your done!

Oct 05, 2009 | 2006 Ford Taurus

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
2006 Ford Taurus Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...