Question about 2000 Isuzu Rodeo

1 Answer

Not lining up properly

Timing belt replacemant instructions and setting and alignment a

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 297 Answers

Http://www.fixya.com/cars/t605372-change_water_pump_in_1996_isuzu_oasis

Discussed before on fixya a bit.

For full story order the appropiate Haynes or Chilton repair manual.
Maybe in you local library or bokshop. If not order online.

Be aware you can make full damage if you do not understand fully what an engine does.

Posted on May 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put back the timing belt


line up the lines on the belt with the dots on the sprockets and you cant miss.there is also two small dimples on the cover behind the cam sprockets that you can use to line up dots on face of cam sprockets with.the belt should have marks to indicate which side faces outward toward front of vehicle.turn crankshaft until dot on its sprocket is in roughly the five oclock position.align solid line on belt with this dot(area of belt with words on it will need to be between cam sprockets.i find it helpful to wedge a piece of cardboard between belt and lip on oil pump to hold belt in position on crank sprocket.next align the next solid line with the tooth on the DRIVERS cam sprocket that has the dot on it.....this shoul be roughly two oclock position.lastly align the hashed line on belt withdot on passenger side cam sprocket....this will be in roughly the 11 oclock position.loop remainder of belt behind tensioner pulleyand set tension.as long as themarks on the belt line up with marks on sprockets properly you cant miss.

Feb 27, 2011 | 2001 Nissan Frontier Crew Cab

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

2 Answers

I have a 2002 pt cruiser with a 2.4 litre motor. I've tried to install the timing belt but it does not line up with the 4 scrib marks. I do not know how to rotate the cams in the right order for the belt...


It is typical to have to stretch the belt a tad as you install--needs to be tight across the cam sprockets and from the right cam to the crank gear. Then the tensioner should take up the slack on the other side. 0996b43f80209592.jpg
  1. enlarge_icon.gifenlarge_tooltip.gif
  2. Fig. Camshaft and crankshaft alignment marks-2.4L engine

To install:

0996b43f8020873a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Install the belt tensioner


0996b43f8020873b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Proper timing belt routing

  1. Set the crankshaft sprocket at TDC by aligning the sprocket with the arrow on the oil pump housing.
  2. Set the camshafts timing marks so that the exhaust camshaft sprocket is a 1 / 2 notch below the intake camshaft sprocket.
  3. Install the timing belt by starting at the crankshaft. Go around the water pump sprocket, idler pulley, camshaft sprockets and the tensioner.
  4. Move the exhaust camshaft sprocket counterclockwise to align the marks and to remove any slack.
  5. Insert a 6mm Allen wrench into the tensioner opening on the top plate of the tensioner pulley. Rotate the top plate counterclockwise. The pulley will move against the belt and the tensioner setting notch will start to move clockwise. Continue to move the top plate counterclockwise until the setting notch is aligned with the spring tang. Using the Allen wrench, to prevent the top plate from moving, tighten the tensioner lock bolt to 220 inch lbs. (25 Nm). Make sure the setting notch and spring tang are still aligned after the lock nut is tighten. If not repeat the procedure.
  6. Remove the wrench from the belt tensioner.
    NOTE When repositioning the crankshaft to the TDC position, this must be done during the clockwise rotation movement. If the TDC is missed, rotate a further two full turns until TDC is reached. Do not rotate the crankshaft counterclockwise as this will result in improper tensioner settings.
  7. Rotate the crankshaft two full revolutions and verify that the TDC marks are properly aligned.
  8. Check the spring tang is within the tolerance window, if not repeat the previous two steps.

Aug 28, 2010 | Chrysler PT Cruiser Cars & Trucks

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

How do I set a timing belt for a 1989 Mazda 929


You need to get a manual. Try the Haynes manual for your car. Try autozone; generally available for around $20. This is not the type of thing that can be covered here in enough detail to do you any good. You need a picture.
Buy new timing belt. Disconnect negative battery cable. Remove timing belt cover. make sure cylinder #1 is set at TDC. making sure all components are properly aligned and loosen pensioner to remove old timing belt. Install new timing belt. Tension belt, ensure all components are aligned properly, replace timing belt covers and reconnect battery.

Feb 20, 2010 | 1989 Mazda 929

2 Answers

Gday fellas need to know how to set timing after head replaceme


Okay...here ya go...you didn't post what type of motor so please choose the correct one for your application.

Valve timing alignment marks — E-Series engines

8ac0809.gif


Valve timing alignment marks — CA16DE and CA18DE engines

ba12ead.gif

Jun 30, 2009 | 1988 Nissan Pulsar

4 Answers

Timing mark locations on EJ22 subaru engine


Complete instructions including pictures for the 22 http://www.subaruvanagon.com/tom/Timing%20Belt.htm

May 09, 2009 | 1991 Subaru Legacy

2 Answers

Timing belt alignment


A factory service manual would help, but I'm assuming that if you had one, you probably wouldn't be on this site.

To set the timing, you need to first perform the obvious: remove the accessory drive belts, cam pulley covers, and engine fan and hub. Next you'll need to rotate the engine by hand until the timing marks on the camshaft sprockets and crankshaft are aligned with their corresponding stationary marks. The 0 degree mark on the lower timing belt cover is the timing mark for the crankshaft pulley. There is a mark (small, vertical formed indentation) for the left camshaft pulley on the backing plate behind the pulley near the 1 o` clock position. The same mark exists for the right camshaft pulley only it is on the backing plate near the 8 o`clock position (making it difficult to see). With the crankshaft placed at the zero mark, you can observed where the timing discrepancy exists.

(TIP: Once the right camshaft timing is properly lined up, etch an additional mark on the pulley's face and the backing plate at the 12 o`clock position. This will make it easier to align the pulley for furture adjustments and repairs)

To set the timing correctly, move the crankshaft pulley to 12 deg. BTDC. Being careful to not disturb the position of the crankshaft once it has been moved to that position, remove the crankshaft pulley, lower timing belt cover, timing belt tensioner, and timing belt. Compress the timing belt tensioner and if the original ring pin isn't available to retain the tensioner a small allen wrench can be used to achieve the same results. Line up both camshaft marks and reinstall the timing belt and timing belt tensioner (do not remove the timing belt tensioner tool used to maintain the tensioner piston in a compressed position). When installing the timing belt, be sure to allow the least amount of slack to exisit between the left camshaft pulley and the crankshaft sprocket, but without moving the pulleys.

Next, remove the timing belt tensioner piston retention tool and mount the lower timing belt cover and crankshaft pulley (without fully installing them). Rotate the crankshaft pulley to the 0 deg. mark. If done correctly, moving the crankshaft pulley from 12 deg. BTDC to 0 deg. will remove all remaining slack from the timing belt assembly and the camshaft pulleys and crankshaft pulleys will be lined up with their corresponding marks. Once proper timing has been achieved, install all removed parts.

(Another TIP: I hope it's not necessary, but in case it is, I'll remind you that proper torque of all bolts are necessary as this is an all aluminum engine. Stripping out bolts holes due to over-tightening bolts occurs very easily and become very annoying to deal with [e.g. alternator belts not being able to be tightened completely and constantly squealing every few days, etc.])

Apr 26, 2009 | 1997 Isuzu Rodeo

2 Answers

Replacing timing belt on daewoo nubira 2000 model


Instructions Difficulty: Moderate Things You’ll Need:
  • Set of ¼-inch drive sockets ¼-inch drive ratchet Set of ½-inch drive sockets ½-inch drive ratchet Set of 3/8-inch drive sockets 3/8-inch drive ratchet Set of metric wrenches Floor jack Jack stands
Step1 Raise and support the vehicle on jack stands. Remove the intake air temperature wiring, the breather hose and intake air hose. Take off the air cleaner assembly. Step2 Remove the right wheel. Remove the accessory belts. Remove the crankshaft bolt and the crankshaft pulley. Remove the power steering bolts and the timing belt covers. Temporarily install the crankshaft bolt and turn the engine clockwise until the mark on the crankshaft pulley, which is a triangle stamped into the crank sprocket, is aligned with the corresponding triangular mark on the block. Step3 Make sure that the timing marks are aligned on the camshaft sprockets. These are a line on each sprocket that runs through a tooth on each sprocket. These lines should line up in the middle between each sprocket and point toward each other. If they do not line up, turn the crankshaft one more time and they will line up. It takes two turns of the crank to one complete revolution of the cam. Step4 Loosen the water pump bolts; using the 3/8-inch ratchet, turn the water pump clockwise away from the belt and loosely tighten the bolts to keep it there. Remove the timing beltmag-glass_10x10.gif. Make sure the timing marks are aligned and install the new belt starting on the right side from the crank sprocket and working counterclockwise. Keep all the belt tension on the right side away from the tensioner. Step5 Loosen the bolts in the water pump and rotate the water pump counterclockwise to apply tension to the belt. Watch the tensioner, which is above the water pump, and apply tension with the water pump until the pointer on the tensioner lines up with the notch above it. Lightly tighten the water-pump bolts. Step6 Turn the engine two more times and align the timing marks perfectly. Loosen the water-pump bolts and, using the ratchet, apply tension to the belt until the tensioner pointers are aligned. Tighten the water-pump bolts. Step7 Install the timing-belt covers and the bolts in the power-steering pump and tighten. Remove the crankshaft bolt and install the crank pulley and the bolt, then torque the crankshaft pulley bolt to 70 foot pounds of torque. Install all components in reverse order of removal.

Mar 02, 2009 | 2000 Daewoo Nubira

2 Answers

Timing belt replacement problem


old timing belt stretched

you only hand turn twice

get number one cyl up on compression stroke both vales closed piston to top of stroke

put the cam with the tooth out to align marks

try again

unless you are 180 deg out should be right




249564_graphic_190-xqmerumdoccwaz0yonnflzbd-2-0.jpg

Apr 13, 2017 | 1997 Toyota 4Runner

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...