Question about Mazda MX-6

1 Answer

Need instructions on how to change it

I need to change a air flow sensor in a 1993 mazda mx6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Please forgive me if the images do not show up. please do not forge to rate and comment about your experience with fixya today. Removal & Installation

  1. Disconnect the negative battery cable.
  2. Loosen the hose band and remove the intake hose.
need instructions on how to change it - 89544p13.gif To remove the mass air flow sensor, first detach its wire harness connection
89544p14.gif Next, remove the sensor-to-air cleaner housing retaining bolts and loosen the air intake pipe clneed instructions on how to change it - 89544p15.gif 89544p15.gif Pulneed instructions on how to change it - 89544p16.gif out of the air cleaner housing
89544p16.gif Inspect the air flow sensor sealing ring and replace as needed
  1. Remove the airflow meter attaching bolts and detach the wire harness connector.
  2. Remove the airflow meter from the air cleaner housing.
  3. Installation is the reverse order of the removal procedure.

Posted on Apr 17, 2009

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my diagnostics connection located on my 93 mazda mx6 4 cylinder?


For 1993 Mazda MX-6 2.0L MFI DOHC 4cyl the OBD Diagnostic Link Connector is located: Under hood, driver side, upper engine area, passenger side rear of air filter housing, mounted next to airflow meter connector.

Hope this helps (remember to rate this free answer)
.

Jun 04, 2011 | 1993 Mazda MX-6

1 Answer

I have a 91 mazda mx6 it will turn over but will not always fire up,but when it does it may run for a long time or it may die rite away and then sometimes it'll start up and sometimes I can crank the batt....


Check the air intake tube that goes to the throttle body, Check for cracks or leaks, This can cause unmetered air to get by the mass air flow sensor

Mar 13, 2010 | 1991 Mazda MX-6

1 Answer

94 mazda mx6 wont start,getting fuel, got spark, what could it be?


First check your air flow to your intake. To have combustion you gotta have fuel, spark, and air. Also check your MAF (Mass Air Flow Sensor) This is located just before the intake. If its not this, your engine timing may be off.

Jan 07, 2010 | 1994 Mazda MX-6

1 Answer

1993 mazda mx6 idles jumps up and down between


The butterfly at the air intake may be dirty. If at all possible remove the breathers leading to this and clean the butterly with carbuerator cleaner or something like it. There may be deposits and it is not breathing good.

Oct 09, 2009 | 1993 Mazda MX-6

2 Answers

I just need to know the location of the engine thermostat on a 93 mazda mx6


If its the v6 it is located on the right side of the motor just follow the top right radiator hose to the case the thermostat is located in.

Apr 25, 2009 | 1993 Mazda MX-6

1 Answer

Sensor directly behind the air filter


93??? think its a carburettor

Mar 17, 2009 | 1993 Mazda MX-6

1 Answer

Cold Air Intake - Mass Air Flow Sensor Adapter


i have a 91 mx6. the intake is all cattywompus and im just goin to take a piece of metal and tube and cut a hole in the peice of metal and weld the tube to it take my stupid box out and run that pipe staight to a coupling and then to the cone air filter. BAM!!!! problem fixed... i maight be able to fix yours too... e-mail me ajjordan64@hotmail.com. k?

Feb 28, 2009 | 1993 Mazda MX-6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...