Question about 1993 Toyota Camry V6

1 Answer

I want to replace the driver's side mirror and need to remove the inside door panel thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Here is step by step instruction to remove your door panel. i am not sure if the picture are coming through so please forgive me on the images. please do not forget to rate and comment about your experience today wih fixya Front Door

  1. On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.
I want to replace the - 89550p12.gif Using a taped prytool, carefully remove the bezel portion of the handle
89550p14.gif Remove the bezel by pulling towards the tip of the handle
89550p15.gif Remove any screw covers ...
... and extract any retaining screws from the door panel
  1. Remove the screw from the inside handle and slide the handle forward. Disconnect and remove the handle from the control link.
  2. On manual mirrors, remove the setting screw and knob. Tape the end of a thin flat-bladed tool and pry the retainer loose to remove the cover.
  3. If equipped with power windows, remove the power window switch from the and armrest.
  4. Remove the mounting screws and remove the armrest from the door panel. Remove the inside door handle bezel by pushing I want to replace the - 89550p18.gif />
89550p18.gif Carefully pry the edge of the door panel around I want to replace the - 89550p13.gifges, then remove the door panel
89550p13.gif Once the door panel is removed, make sure to disconnect all wiring
  1. Remove the door courtesy light by pulling outward. Disconnect the electrical wiring.
  2. Remove the two screw caps and speaker cover(s). Remove six screws from the trim panel.
  3. Remove the door pocket from the panel.
  4. Tape the end of a thin bladed tool, then insert the tool between the door panel and door and pry the panel outward. Disconnect the electrical wiring after the panel is free and remove the panel from the vehicle.
To install:
  1. Connect the electrical wiring, if equipped, and install the trim panel onto the door.
  2. Secure the trim panel with the mounting screws, then install screw caps and speaker cover(s).
  3. Install the door pocket.
  4. Install the armrest and secure with the mounting screws. Install the power window switch as required.
  5. Install the door courtesy lamp. Install the inside handle bezel.
  6. Install the outside rear view mirror cover and retainer.
  7. Connect the inside handle to the control link. Install the handle, slide it rearward and install the screw.
  8. With the door window fully closed, install the window regulator and handle.

Posted on Apr 17, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: removing door panel drivers side to connect mirror wiring behind this panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

countrysi248
  • 443 Answers

SOURCE: I need to remove the door panel on my 2004 Avalanche

There are plastic clips that hold the door panel inplace .. First look for any hidden screws near the door handle . there might be a little plastic cover that you need to remove with a small screw driver to find the screws.. look under the handle also to see if there are any hidden screws . next take a flat blade screw driver and start at the bottom corner and try gently prying the door panel off . try to stay close to the plastic clips not to damage them by prying real hard .. once you have snapped them loose all the way around .. lift up on the door panel to remove it from around the window lip and out it should come.. holler if you have any problems.. usually The mirrors on the chevys are up above the panel and there is a triangle plastic cover over it on the inside .. it will pry off also gently and there are 3 nuts there that need to be removed .. use caution these fall behind the door panel ... holler if you need more. Jerry

Posted on Apr 24, 2009

  • 187 Answers

SOURCE: How do remove drivers side door panel

First you need to remove the door handle and window crank by pushing back the ring and releasing the handles. Also the arm rest will have screws into the steel door frame that must be removed. The panel itself has plastic snaps that are pushed into holes in the doors steel frame. The trick is to slide a pry bar or even two is better, one on ether side of the clip and force the pin out. You need to be patent and do one at a time. The door panels are made of a less than hard strong material and will brake apart easily especially if they are older. The clips go all the way around the lower three sides and the top will lift off the sill.

Posted on May 07, 2009

  • 69 Answers

SOURCE: How to remove/replace driver's side mirror on 96 blazer

remove door panel.. there should be access hole to get to the bolts.

Posted on Jul 31, 2009

  • 1986 Answers

SOURCE: I need to remove the door panel on my 2004 Avalanche

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them.

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to replace drivers side rear view mirror, powered. I have the new mirror, just need to know how t install it.


Hi,
You remove the door panel on the inside and it is bolted on from the inside. One wire clip and 3 bolts. Takes longer to remove and replace the door panel than replace the mirror....look for a hidden screw under the armrest , under the window/door lock button panel and sometimes behind the reflector or light on the bottom of door..Usually there are 3-4 screws and then the rest of the panel is held on by plastic clips. Get the screws out, then work a flat screwdriver or putty knife around the sides and bottom of panel, then lift upwards to get the top sealing side out of the track where the window runs.....Mike

Jul 14, 2011 | Buick LeSabre Cars & Trucks

1 Answer

Describe how to replace 2002 driver side mirror


remove the left door panel screws by inside handle and remove the 2 big screws in the arm rest may have some covers on it then with the panel clip tool or screw driver you need to hit the inside top of the panel as you lift up with you hand dont break the panel. carefully remove the door panel clips to release the panel. remove the screws inside the door at the mirror unplug the connector have someone hold the mirror so you dont scratch the car. then pull it loose and reverse the prosess.

Dec 11, 2010 | 2002 Oldsmobile Bravada

1 Answer

2003 Navigator: remove driver-side Power Mirror


no need to remove the door.. just open the screws of the inside concole , opening handle and lever .. take out the console and u will see the screws to open the mirror.

Jul 29, 2010 | 2003 Ford Expedition

2 Answers

2001 camry replacing driver side mirror


Pull off the triangular trim panel that is right behind the mirror. It is held on by 2 clips. This will allow you to see all three 10 mm bolts to remove the mirror.

Mar 22, 2009 | 2001 Toyota Camry

1 Answer

PASSENGER MIRROR


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 22, 2009 | 1998 Plymouth Breeze

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

3 Answers

Replacing the Mirror Light - driver's door


I assume your question is how to replace the bulb in the side mirror. Can you please tell us the make and model of the car.?
Thanks,

Jan 24, 2009 | 2002 Volvo S80

2 Answers

Instructions for replacement of side view mirror


the door panel near the mirror must be removed if not the entire door panel inside u will find 3 nuts to remove to get the old mirror off. hope this helps please rate me

Jan 12, 2009 | Pontiac Grand Prix Cars & Trucks

1 Answer

Need to replace driver side mirror for Camry 2002, Power mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Dec 05, 2008 | 2002 Toyota Camry

1 Answer

Replacing a drivers side mirror


There is a panel on the inside of the door where the mirror is.
That has to come off.
In some cases the door panel has to come off also.
Under the mirror panel there are nuts that hold the mirror on. Remove the nuts unplug the harness and install the new one.

Oct 07, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

521 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...