1992 Isuzu Trooper Logo
Sue Baldock Posted on Sep 17, 2013

Isuzu Bighorn 3.1 auto import 1993/4 - speedo stopped working at same time as check transmission light has started flashing - it won't drop into top gear

1 Answer

cornelius

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 13 Answers
  • Posted on Sep 17, 2013
cornelius
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that hasĀ over 10 points.

Problem Solver:

An expert who has answered 5 questions.

Joined: Sep 17, 2013
Answers
13
Questions
1
Helped
2512
Points
39

Replace the speed sensor on the rear of the transmision and posibly the drive gear its plastic so it does not last

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Sep 19, 2008

SOURCE: 93 isuzu bighorn

a temperature sender located at the thermostat housing was found to be faulty sending permanent earth to tranmission making the overdrive gear inoperable . when replaced the vehicle achieves 100kph from 2500 rpm as true.

Ad

Anonymous

  • 1124 Answers
  • Posted on Jul 08, 2009

SOURCE: 2000 ISUZU TROOPER WITH AUTO TRANSMISSION. CHECK

If the fluid is up -
it could be a vacume loss or the shifting module..
The shifting module is what tells it to shift - and it is controled by vacume pressure..

stevenhurc

Steve Hurc

  • 459 Answers
  • Posted on Jul 29, 2009

SOURCE: Speedo stopped working

check wire/wiring connector on right rear section of transfer case.
disconnect wire connector and remove and inspect gear drive for worn teeth including gear inside case.

Anonymous

  • 10319 Answers
  • Posted on Aug 18, 2010

SOURCE: 1996 Isuzu Bighorn 3.1 diesel

Have the governor checked out. It sounds like the spring is weak. It does reset after shutting off the engine

A

Anonymous

  • Posted on Dec 20, 2010

SOURCE: 1993 Isuzu Bighorn 4jg2 Auto. OD light flashing

The reason why your OD light is flashing is the speed limiter in the dash will need to be replaced. It could also mean that your over drive switch on the gear lever has gone bad. The best thing to do is plug in a OBD II scan tool (on board diagnostics) and obtain the trouble code stored inside your Isuzu vehicle computer.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My ISUZU BIGHORN 2005 automatic transmission is u=not running even the engine is on..what seems to be the problem??

www.fixya.com/cars/t3327109-isuzu_bighorn_automatic_transmission

5 answers
Nov 1, 2009 - Hi, i have got Isuzu Bighorn 3.1D 1993 model. ... When it slips it cant move even if yourave up the engine or even you you put in D1,D2,L.. ... Not check levels first. ... oil gets to hot and it also raises the heat-gauge, engine runs to hot. .... permission from Fixya Ltd. Ā© 2005-2015, Fixya, Ltd. or it's affiliates. My 3.1 diesel Isuzu bighorn automatic transmission
11 answers
Jun 6, 2016
How to check transmission fluid on 2001 isuzu rode
2 answers
Nov 18, 2008
More results from www.fixya.com
0helpful
1answer

O/d light flashing on Isuzu Bighorn, 3.1 diesel, auto g/box

the oD lamp doing that means scan me. on all cars..... use any scan tool of 1996 or newer. if not ,use the flash codes... ask.
no year stated! and FAILS
older post.
11helpful
1answer

1993 Isuzu Bighorn starting problems

The breakdown service in Nz says it is a problem with the auto transmission being a switch which is not acknowledging it is fully engaged in park, therefore, wont start. I have similar problem, he says to start it in Neutral when this happens. Not sure if this will work for you, but worth a try.
15helpful
5answers

Isuzu bighorn automatic transmission slips after heating

Change your gearbox oil, and clean out the oil strainer.
Should help.

( On some models, you have to remove the gearbox oil pan to clean the strainer )
1helpful
1answer

Speedo stopped working

check wire/wiring connector on right rear section of transfer case.
disconnect wire connector and remove and inspect gear drive for worn teeth including gear inside case.
1helpful
1answer

Check trans light on

there are 2 possible problem and solution. 1st check your RPM sensor located in the transmission.(less expensive part). if this does not work. got to option 2 which is the computer box, try to consult an expert computer box technician to repair it or buy a new comp box. but before buying... be sure all electrical connections are good and no additional accessory are connected to the wirings.bad connections and circuits may lead to damage comp box.
0helpful
1answer

1993 bighorn transmission - Automatic

if it is jumping gears, the gear box will not do that, it is more than likely your sedondary inside the transmission.
2helpful
2answers

I have a 3.1 auto bighorn and the auto transmission from time to time plays up by jumping and seems to slip. Also the speedometer reading drops to zero and no mileage is recorded. I don't think its a...

the speedo sensor is at the back of the transmission and it controls the overdrive or last two gears.this is an electrical switch and needs to be replaced.
0helpful
1answer

Isuzu Bighorn transmission

My Torque on demand and 4 hi/low flashed for a couple days then stopped on it's own. There is a sensor somewhere under the truck that gets dirty from I was told.
Not finding what you are looking for?

1,059 views

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...