Question about 2005 Hyundai Sonata

1 Answer

2005 Hyundai sonata 6 cylinder remove intake manifold to replace rear spark plugs, how many bolts are there in the rear? It would help if I could get a step by step way to remove the manifold.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 67 Answers

There are 3 bolts in the back1 on left 1 in middle and 1 on the right. hope that helps

Posted on Apr 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the knock sensor located on a 2011 2.4 engine hyundai sonata?


On-Line Service Manual is available on the following website:

http://www.hsguide.net/hyundai_sonata_yf_2011_year_service_manual-6.html

Hyundai Sonata: Knock Sensor (KS). Repair procedures:

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Remove the intake manifold (Refer to "Intake And Exhaust System" in EM group). 3. Disconnect the injector connector (A). 4. Remove the installation bolt (B), and then remove the sensor from the cylinder block. syffl0041n.gif

Installation
caution_icon_eng.gif • Install the component with the specified torques. • Note that internal damage may occur when the component is dropped. If the component has been dropped, inspect before installing. 1. Installation is reverse of removal. Knock sensor installation bolt: 18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
knock sensor-m3h04eiq4trf45oprzz0vy4e-2-0.jpg

Knock Sensor/Parts are available on the following website:
http://www.partsgeek.com/ymm/2011/hyundai/sonata.html?category=engine_electrical&part=knock_sensor

May 22, 2017 | Hyundai Cars & Trucks

Tip

How To Change The Spark Plugs On A 2002-2005 Kia Sedona 3.5 Liter


You'll need to remove the oil cap and the 6 bolts holding on the engine cover. The front 3 spark plugs are pretty easy to replace. You'll need to unplug the spark plug wire from the coil and disconnect the electrical connector. Unbolt the 2 10mm bolts holding the coil to the valve cover. Twist the coil and boot back and forth and pull it out of the cylinder head. The spark plug is down in the head, you'll need at least a 6 inch extension with a 5/8" spark plug socket, a telescopic magnet will help get the spark plug out of the head. The back 3 spark plugs involve removing the upper intake and throttle body, unbolt the bracket to the throttle body, and the bracket bolted to the upper intake manifold. on the back side of the engine. Remove the tubing from the throttle body to the air cleaner box. Unbolt anything else bolted to the upper intake. Unplug electrical connectors to the throttle body and any other electrical connectors on the upper intake and remove the upper intake bolts. And move the upper intake out of the way, there are only spark plug wires on the back 3 plugs. Twist and turn each boot to aid in removing the boot from the plug. I would get a new upper intake gasket and consider replacing the wires at this time also. There are actually only 3 spark plug wires, so for what is involved to get to them, I would replace them. I have found alot of the wires will arc to the upper intake manifold.

on May 02, 2010 | Kia Sedona Cars & Trucks

1 Answer

How do i remove intake manifold on 2005 pt cruiser 4 cylinder


there is a 2 part. just take off the one going over the valve cover. it has 6 -10mm bolts

Feb 11, 2013 | 2005 Chrysler PT Cruiser

1 Answer

How to change spark plugs on a Hyundai Sonata 2.7 liter V-6 ?


This is listed as a 2.6 hours operation in the labor guide, so be aware that it could take you that amount of time or substantially longer. The left side is fairly easy after you remove the spark plug wire cover. The right side is the most difficult because it requires removing the upper intake manifold which is estimated at about 2 hours alone.

May 29, 2011 | Hyundai Motor 2004 Sonata

2 Answers

How many spark plugs are on the mercury milan 2007. I only found 3.


For 2007 Mercury Milan 3.0L SFI DOHC 6cyl the upper intake manifold must be removed to access the RH spark plugs only.
  1. Remove the upper intake manifold, if removing the RH spark plugs. Refer to the Intake Manifold procedure in the Engine Mechanical Section
  2. Disconnect the 6 ignition coil-on-plug electrical connectors.
    NOTE When removing the ignition coil-on-plugs, a slight twisting motion will break the seal and ease removal.
  3. Remove the 6 bolts and the 6 ignition coil-on-plugs.
    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.
    NOTE Use compressed air to remove any foreign material in the spark plug well before removing the spark plugs.
  4. Remove the 6 spark plugs.

To install:
  1. Inspect the spark plugs, as outlined in this section.
  2. Inspect the 6 spark plugs.
  3. Adjust the spark plug gap, as necessary, to 1.32-1.42mm (0.052-0.056 in.).
    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.
  4. Install the 6 spark plugs. Tighten to 15 Nm (11 lb-ft).
    NOTE Apply a small amount of dielectric grease to the inside of the ignition coil-on-plug boots before attaching to the spark plugs.
  5. Install the 6 ignition coil-on-plugs and the 6 bolts. Tighten to 7 Nm (62 lb-in).
  6. Connect the 6 ignition coil-on-plug electrical connectors.
  7. If removed, install the upper intake manifold

Hope helps.

Mar 07, 2011 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

Spark plug cylinder


For the 2005 Hyundai Sonata
I do not know if you have the 2.4L In-Line 4-Cylinder or 2.7L V6; however I have included both below....

For the 2.4L In-Line 4-Cylinder:
Firing Order:
1-3-4-2
Cylinders:
..........(back).........
|...1....2....3....4...|
.........(front)

For the 2.7L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.......(back)........
|...1....3....5...|
.......................
|...2....4....6...|
.......(front)
Coil Connections:
(back)
...3
...6
...2
...5
...4
...1
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Jul 02, 2010 | 2005 Hyundai Sonata

1 Answer

Change sparks plugs on 06 hyundai sonata v6


You didn't specify whether you have the (4) cylinder or the (6) cylinder engine..... I have a 2004 Hyundai Sonata 2.4L 4 cylinder and I just changed the spark plugs in it. I believe that the 2005 2.4L engine is the same. To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine: Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way. Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed. Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place. Repeat same procedures for spark plugs number (3) and (4). Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold

Jul 08, 2009 | 2006 Hyundai Sonata

1 Answer

2004 Hyundai Sonata 6 cyl


Depends on how MECHANICALLY INCLINED you are. Have you done any repair work on vehicle engines before? It's not that difficult to do if you know how to turn a wrench/ratchet and THINK about what you are doing and what you are dealing with... .attention to details. Ya think? On the 04 2.7 lit V6 Sonata, there are two nuts and 5 bolts (two long and three short) which hold the plenum to the RISER manifold. There are an additional 3 to 4 bolts at the rear (firewall side) which support the plenum (they're all 12mm bolts). You'll need to remove the intake air hose to lift the plenum out of the way to access the 3 plugs on the RH side (rear) of the engine. You'll want to replace the plenum gasket when you do this. When you reinstall the plenum, the tightening torque is 11-14 lb.ft. Do not tighten the REAR support bolts until after you torque the surge tank bolts to the intake (riser) manifold.
ab1cefd.jpg

Jun 13, 2009 | Hyundai Motor 2004 Sonata

1 Answer

I can't find the spark plugs in my 2005 sonata


To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine:
Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way.
Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed.
Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right.
Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place.
To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place.
Repeat same procedures for spark plugs number (3) and (4).
Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold.


please rate!

Mar 18, 2009 | 2006 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...