Question about 2001 Dodge Durango

2 Answers

I cant get the axle out of the front diff what is holding it in 2001 dodge durango

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

Here is a diagram on how to get the front pinion seal out and it does mention how to get the axle loose. please do not forget to rate and comment about your experience with fixya today.

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove both half shafts.
  3. Mark propeller shaft and pinion flange for installation reference.
  4. Remove front propeller shaft.
  5. Rotate pinion gear three to four times, to verify pinion rotates smoothly.
  6. Record pinion flange rotating torque with an inch pound torque wrench for installation reference.
  7. Hold flange with Holder 6719 and four bolts and washers.
  8. Remove pinion nut.
  9. Remove flange with Remover C-452.
  10. Remove pinion seal with a pry tool.
    i cant get the axle out of the front diff what is - 67189-dako-g28.gif Removing the companion flange
    67189-dako-g25.gif Measuring pi cant get the axle out of the front diff what is - 67189-dako-g27.gifque
    Pinion seal installer
    67189-dako-g26.gif Tightening the pinion nut
To install:
  1. Apply a light coating of gear lubricant on the lip of pinion seal.
  2. Install seal with Installer C-3972-A and Handle C-4171.
  3. Install pinion flange onto the pinion with Installer C-3718 and holder.
  4. Hold pinion flange with Holder 6719A.
  5. Install new pinion nut and tighten nut until there is zero bearing end-play.

    CAUTION Do not exceed the minimum tightening torque when installing the companion flange at this point. Damage to the collapsible spacer or bearings may result.
  6. Tighten pinion nut to 271 Nm (200 ft. lbs.).

    CAUTION Never loosen pinion nut to decrease pinion bearing rotating torque and never exceed specified preload torque. If preload torque or rotating torque is exceeded a new collapsible spacer must be installed.
  7. Record pinion flange rotating torque, with a torque wrench. Rotating torque should be equal to the reading recorded during removal plus an additional 0.56 Nm (5 inch lbs.).
  8. If rotating torque is low, tighten pinion nut in 6.8 Nm (5 ft. lbs.) increments until rotating torque is achieved.

    CAUTION If maximum tightening torque is reached prior to reaching the required rotating torque, the collapsible spacer may have been damaged. Replace the collapsible spacer.
  9. Install propeller shaft with reference marks aligned.
  10. Install half shafts.

Posted on Apr 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do I get the front axel shaft off

Posted on Jul 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 dodge Durango. It's making a noise that sounds like a bearing that's going out. I've checked over the whole front end drive assembly and have narrowed it down to the front axle chunk. I'm...


drive the truck in a safe place turn left to right you will here a noise change from the left or the right the weight shift will indicate what side. fluid level should have a bolted plug either in the center of the diff or left or right side of it put pinky in first knuckle bend down if fluid on finger it is ok.

Mar 07, 2015 | 2003 Dodge Durango

1 Answer

Front left wheel grinds when you put my 2001 dodge Durango when you put itin 4 wheel drive..how do I fix this?


The c/v axle and output shaft on the front axle are worn where they spline together, they need to be replaced

Dec 14, 2014 | 2001 Dodge Durango

1 Answer

Durango AWD


The vehicle is always in AWD and that cannot be altered . There is a 3rd diff in the gear box that allows independent operation of the front and rear wheels to prevent drive line wind up . When you select 4WD you lock up that 3rd diff so that both front and rear axles have to turn. This results in drive line torque wind up so the vehicle must not be driven in this mode on hard surfaces as there is no means for the wheels to slip and relieve the torque wind up . To loose the wind up reverse for several yards and any actuators that are trying to move will be able to or drive on slippery surfaces to allow the wheels to slip

Mar 08, 2014 | 2001 Dodge Durango

1 Answer

Humming noise sounds like from the front end. I just replaced wheel hubs and still making noise. The tone of the humming changes with slight on off the gas pedal. I just ordered new front axles thinking...


check side carrier bearings in the diff i have rreplace a lot of them for the same noise thats all you have to do remove the diff cover remove end caps and see if the bearings are pitted if so replace

Jan 13, 2013 | 2000 Dodge Durango

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

1 Answer

I need to pull the whole rear diff and axles out of 01 durango what is easiest?


put jackstands under the frame and start taking everything loose that has to do with the rear end. springs, shocks driveshaft, and brake lines

Oct 26, 2010 | 2001 Dodge Durango

1 Answer

2001 dodge durango 4 wheel drive not working loud knocking


You need to check the cv joints in the front end or the u joints in the front drive shaft.If none of the above then the problem is internal in the front diff.

Jan 28, 2010 | 2001 Dodge Durango

Not finding what you are looking for?
2001 Dodge Durango Logo

690 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...