Question about 1992 Toyota Pickup

1 Answer

1992 toyota pickup need to change the cluch. is there a easy way to do this.???

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

No easy way.you will need a jack and stands metric tools disconeck batery remove starter and drive line remove shifter ther are 6 bolts you can axis them from the inside of truck by removeing the shifter boot.place a jack under the trasmition remove the trasmition mount and then remove the 6 bellhouseing bolts 14.mmbut first disconeckall wires from the tansmition after all this is you may need help to lower the trans.6 12mm bolts hold the cluch inplace remove and replace cluch.repet proses should take 3hrs to do this

Posted on May 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the speed sensor on my 89 toyota pickup


some mount in transmission, others mount behind the wheels (one or more)
easy swap

12_11_2012_11_25_10_am.jpg

Dec 10, 2012 | 1992 Toyota Pickup

1 Answer

Were do you change the gear oil on a 1992 toyota P.U. 4x4. On top of tran. or is it one of the two bolts that are on the face of the differential gear box?


please explain the layout ,is it 4x4 ,manual or automatic transmission ,either way the drain plug will be on the lowest point of the gearbox so dont go undoing bolts without knowing ,the drain plug will also have a square drive set into the head so its easiely identifiable

Feb 10, 2011 | 1992 Toyota Pickup

1 Answer

I have a 1992 toyota sr5 pickup 4 wheel drive. I have changed the brake pads on the front and bleed the lines for air. Brakes went on fine and after bleeding the brakes I thought everything was ok. But,...


Some Toyotas need to be cross-bled. You should also check your bleeder valves to make sure you tightened them securely. Look for leaks at the master cylinder and possibly a rear wheel cylinder. Re-bleed the system.

Jun 23, 2010 | 1992 Toyota Pickup

1 Answer

1992 Pickup: how to change a starter on 92 toyota pickup...


disconnect the battery take the power wires off the starter turn the bolts counterclockwise pull up slightly on the starter and pull out reverse process to reinstall.

May 07, 2010 | 1992 Nissan Pickup

1 Answer

Ware is the fuel filter on 1992 toyota 4x4 pickup


1992 toyota pickup 4wd V6 3.0L SOHC. The fuel filter is located on the right frame rail underneath the passenger compartment.

Mar 28, 2010 | 1992 Toyota Pickup

1 Answer

How to change the air conditioner cluch bearing


you need to discharge the ac and remove the compressor then remove the bolt on the the front for the clutch then theres a snap ring holding the bearing on wacth out for the little shims in the clutch if you lose them the clutch will be stuck on

Feb 28, 2010 | 1994 Toyota Pickup

3 Answers

88 Toyota Pickup, has become difficult to shift in to gear. Once in gear (1,2,3,or4th) very smooth. I believe must be something up front in the clutch linkage. Possibly? Can get into, but takes awful...


if your linkage was bent it wouldnt shift into all gears easily.sounds like you need to blead your slave cylinder to your clutch.10mm wrench and bleed it like your brakes same type set up.

Nov 24, 2009 | 1988 Toyota Pickup

1 Answer

Shrill noise coming from around distributor.


I is the timing chain inside the engine rubbing on the cover houseing. You need to have the chain or tensioner replaced or both
Mike

Jul 08, 2009 | 1992 Toyota Pickup

1 Answer

Release spare tire 1992 toyota pickup


first of all get ama or a similar insurance additive, wate, 3 days and have them do it.....otherwise if the release screw is siezed you will have to cut the cable that holds it in place

Mar 29, 2009 | 1992 Toyota Pickup

Not finding what you are looking for?
1992 Toyota Pickup Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...