Question about 1988 Mazda B2200

1 Answer

Can a bad ignition switch cause the truck to die or idle bad? 1988 mazda b2200

Posted by on

  • wadeinaustin Apr 16, 2009

    my 88 mazda b2200 will die unless you turn the idle screw almost all the way up, and when im driving at higher speeds the truck runs fine. sometimes it will just completely shut down on highway. the ignition switch also in was told needs replaced for other reasons, and i was wondering if this could be connected thank you

  • yadayada
    yadayada May 11, 2010

    in most cases no.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Yes, bad ignition switch can cause that, did on my B2200.

Posted on Dec 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 MAZDA B2200 DIES AND WONT START UNTIL IT SITS AWHILE HAS NO FIRE TO SPARK PLUGS WHEN THIS HAPPENS


I'd say the coil is shot. However when ot does happen make sure you still have 12volts going to the coil. This will help eliminate wiring issues.

Jul 12, 2014 | 1988 Mazda B2200

1 Answer

1990 mazda b2200 2.2l fuel injected won't accelerate just bogs down idles fine


I think you have established that it is getting fuel but I guess what I would do is check into the throttle body itself.

May 20, 2014 | 1988 Mazda B2200

1 Answer

Wont start..no spark computer problem?


many things will cause no spark bad distributor cap or rotor.bad plug wires.ignition timing to far advanced cause by loose distributor.could have faulty ignition coil or module.check ignition fuse.probably could be faulty PCM i would have it checked out.could have bad crankshaft sensor.

Aug 01, 2013 | 1988 Mazda B2200

2 Answers

Idling problem


need to adjust idle speed by turning air adjusting screw on throttle body idle should be 750 - 790 RPM. make sure spark plugs and wires okay. make sure distributor cap and rotor good.replace fuel filter do a little tune because if engine not fine tuned one bad cylinder will cause engine not to idle if you have fuel injection system clean fuel injectors by filling gas tank full add a can of seafoam to fuel tank see what happens.

Jul 29, 2013 | 1988 Mazda B2200

1 Answer

Electrical Issues B2200


Your alternator is not yet doing anything. Minimum voltage, even with all accessories on, should be around 13.5 volts. Check all fuses, connections, grounds, and wiring. Have the alternator tested if you find nothing amiss.

Dec 03, 2012 | 1988 Mazda B2200

2 Answers

1989 mazda b2200 can not set timing


i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Feb 17, 2010 | 1988 Mazda B2200

1 Answer

I need a vacume diagram for my truck it is idleing


Here is a link that will be very helpfull to you including what you need dont forget to rate my assistance thank you.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Vacuum+Diagrams&partName=Driveability+%26+Emissions+Controls&pageId=0900c15280076be3&partId=0900c15280076b68

Feb 13, 2010 | 1988 Mazda B2200

1 Answer

1990 mazda b2200 starts & idle but dies if I push on the gas.


You need to run a pressure check on the fuel line with the appropriate gauge.

Mar 07, 2009 | 1988 Mazda B2200

1 Answer

Will not start, no spark


get spark tester and start testing from the spark plugs back. first hook it to aplug wire and check for spark if no spark ten hook it to the coil wire and check for spark if no spark then there is a chance that your coil or ignition module is bad if it is equipt with electronic ignition.

Aug 18, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

609 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...