Cracked bulb and glass on 2009 toyota camry. How do you change the bulbe and glass?

Video Description
The video above shows how to change the fog light bulb in your 2004 Toyota Camry. Not all models have fog lights - for many Toyotas, it depends on your trim level (XLE) or whether the fog light option was ordered when your Camry was manufactured. Fog lights are typically in the front bumper, below the headlight cluster and are helpful in poor visibility. If one fog light is burnt out on your Camry, we recommend changing both bulbs because the working bulb will be dimmer than the one you replaced and will likely burn out soon anyway.

When you change the foglight on your Camry, be careful not touch the glass part of the bulb with your fingers which causes the bulb to burn out earlier.

Other videos you might find helpful

• 
  Replace reverse light White light when you back up - yup, they burn out and you can replace them with bright LEDs
  2003 Toyota Camry XLE 3.0L V6
  
• How to add transmission fluid If your transmission is running low on fluid, be sure to add some - find out how to do this here!
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Complete oil & filter change Sure you can take it in for a $19 lube, but are you OK with a stripped oil pan and cheap parts in return?
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Fix leaky hoses The best way to fix leaking hoses is to replace them, but if you don't have time, a stop leak product might work for you
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• Set the clock to the correct time Is the clock in your car ahead or behind? Learn how to set it here!
  2003 Toyota Camry XLE 3.0L V6
  
• Oil level check Cars burn, leak and otherwise dispense of their oil. Check your level frequently and top up when necessary
  2006 Toyota Camry LE 2.4L 4 Cyl.
  
• See all videos for the 2003 Toyota Camry

Is the bulb ok sometimes you hit a bump real good and pops
the bulb check owner at bulb socket no power relay headlight
in enginecompartment

is the :

fuse ok?
bulb socket ok?
new bulb ok?
power reaching the bulb socket?
ground good?

buy/borrow a cheap multimeter and you can probe your way to where the fault lies

I assume you mean just the bulbs:

1. 1 Shut off the Camry's engine and set the parking brake for added safety. Also, make sure its headlights are switched off.
   
2. 2 Open the hood using the primary and auxiliary hood release latches.
   
3. 3 Locate the back of the headlight assembly and determine whether the low- or high-beam bulb needs to be replaced.
   
4. 4 Turn the headlight bulb socket counterclockwise to remove it from the assembly.
   
5. 5 Unplug the electrical connector from the back of the bulb. Carefully dispose of the bulb to prevent it from shattering or cracking.
   
6. 6 Attach the electrical connector to the new bulb and insert it into the headlight assembly. Twist it clockwise to secure its position.
   
7. 7 Test the new headlight to make sure it works before closing the hood.
   

Thank you,
Lee

You should have to get to the back side of the lamp assembly from under the hood. There should be a cap or dust cover with the wires going thru it to the light. 1/4 turn counter clockwise if it is a hard cap-if dust cap squeeze and pull. There should be a clip that looks like a bent paper clip. Squeeze to release. Change the bulb, reassemble

at that light there should be two screws one on either side take these out and the cover should come off pull the bulb out replace and reverse the process.

there is a bulb housing behind the lens. remove it and the bulb.

probably a bulb most garages will change it for you for small fee. but halfords sometimes help.