Question about 1995 Honda Prelude

1 Answer

Timing belt remove

I cant loosen the timimg belt on a honda prelude 96 model. How to loosen the adjuster arm to loosen the timing belt?

Posted by on

  • mike loshbough
    mike loshbough May 11, 2010

    did you lossen the 14mm bolt on the idler

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 78 Answers

You have to loosen the bolt that goes on the pulley with the arm and spring.

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set crankshaft timing on 1992 honda prelude 2.3 liter?


here is a u-tube video with a good tip for making sure the timing marks dont get move once set may help
How to replace timing belt on Honda Prelude 92 96 2 3 lt H23a1

Jul 28, 2014 | 1992 Honda Prelude

1 Answer

Set timing on a 1992 honda prelude, 2.3 engine, I REPLACED THE DISTRIBUTER AND NOW ITS COMPLETELY OUT OF TIME, detailed instructions please


  1. Locate the service check connector and, if applicable, remove the cap. On 1988-91 Preludes, the cap is yellow and the connector is located next to the vacuum control box in the engine compartment. On 1992-95 Preludes, the service connector is located under the middle of the dash. On 1990-93 Accords, the connector is blue and is located behind the right front kick panel, under the dashboard. On 1994-95 Accords, the service connector is located behind the glove box. Use a jumper wire to connect the two terminals of the service connector.
  1. Following the manufacturers instructions, connect a timing light to the engine. The positive and negative leads connect to their corresponding battery terminals and the spark plug lead to No. 1 spark plug wire.
  2. Make sure that all wires are clear of the cooling fan and hot exhaust manifolds.
  3. Set the parking brake and block the front wheels. Start the engine. Check that the idle speed is set to specifications.
  4. Point the timing light at the timing marks. On all models except 1994-95 Accords, the marks are on the flywheel. On the 1994-95 Accords, the timing marks are on the crankshaft pulley. When the engine is idling, the red mark must align with the pointer. Some timing marks are indicated by 3 lines; the center one must be aligned with the pointer.

  1. If necessary to adjust the timing, loosen the distributor hold-down bolt(s) and/or nut and slowly rotate the distributor in the required direction while observing the timing marks.
  2. To complete the adjustment operation, tighten the hold-down bolt, taking care not to disturb the adjustment.
  3. Switch the engine OFF . Reinstall the rubber plug in the timing window and remove the timing light. Remove the jumper wire.



0900c1528005f368.jpg

Fig. Fig. 4: Service connector on 1988-91 Preludes


0900c1528005f36b.jpg

Fig. Fig. 5: Service connector on 1992-95 Preludes

Mar 03, 2011 | 1992 Honda Prelude

1 Answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?


check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif

Oct 29, 2010 | 2000 Honda Accord

1 Answer

The Haynes manual I have has TWO pages ripped out I have to replace the timing belt can you help me


from autozone.com:
1990-95 4-Cylinder Accord and 1992-95 Prelude
  1. Disconnect the negative battery cable.
  2. Turn the engine to align the timing marks and set cylinder No. 1 to TDC on the compression stroke. Once in this position, the engine must NOT be turned or disturbed. On DOHC Preludes without VTEC, hold each of the camshafts in the TDC position by inserting 5mm diameter punches into the alignment holes just behind each cam pulley.
  3. Remove the splash shield from below the engine.
  4. Drain the engine coolant. Use a clean container; cap or cover the container and wipe up spillage.
  5. Unplug the electrical connector at the cruise control actuator, then remove the actuator. Don't disconnect the cable; simply move the actuator out of the work area.
  6. Remove the belt from the power steering pump. Remove the mounting bolts for the pump. Without disconnecting the hoses, move the pump out of the way.
  7. Unplug the alternator wiring and connectors; remove the engine wiring harness from the valve cover.
  8. Loosen the adjusting and mounting bolts for the alternator and/or compressor. Remove the drive belt(s).
  9. Remove the valve cover.
  10. Remove the side engine mount support bracket, if equipped.
  11. Remove the upper timing belt cover.
  12. Support the engine with a floor jack on the oil pan (use a cushion between the jack and pan). Tension the jack so that it is just supporting the engine but not lifting it.
  13. Remove the side engine mount.
  14. Remove the dipstick and dipstick tube.
  15. Remove the crankshaft pulley bolt and remove the crankshaft pulley.
This bolt is one of the tightest on the entire car. The pulley must be held in place while the bolt is loosened. One trick is to wrap an old drive belt around the pulley to hold it steady-don't try this with a belt that is to go back on the car; it will be stretched or damaged.
  1. If necessary for additional clearance to remove the lower timing belt cover, remove the two rear bolts from the center beam. Slowly lower the jack and the engine until the clearance is gained.
  2. Remove the rubber seal from around the belt tension adjusting nut (do not loosen the nut). Remove the lower timing belt cover.
  3. On all models except Prelude with VTEC, lock the timing belt adjuster arm in place using one of the lower cover (6 x 1mm) mounting bolts.
88d9a40.gif

Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts
There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.

  1. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
  2. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine.
To install:
  1. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
  2. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
  3. Except Prelude VTEC models:
    1. Temporarily install the crank pulley and bolt.
    2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm).
Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
  1. On Prelude VTEC models:
    1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt.
Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is1/4fl. oz. (8 ml).
  1. Make sure all timing marks are positioned correctly (as described earlier).
  2. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
  3. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely.
aa17346.gif Fig. 13: The balancer shaft must be held in position during timing belt installation
  1. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
  2. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures.
Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
  1. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
  2. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
  3. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990-91 Accords, 37 ft. lbs. (50 Nm) on 1992-95 Accords and 43 ft. lbs. (60 Nm) on 1992-95 Preludes.
  4. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following: 1991-93 Accord: 159 ft. lbs. (220 Nm)
  1. Install the dipstick tube and dipstick.
  2. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
  3. Install the upper belt cover.
  4. Install the side engine mount support bracket if it was removed.
  5. Install the valve cover.
  6. Install the compressor and/or alternator drive belt; adjust the tension.
  7. Route the wiring harness over the valve cover and connect the wiring to the alternator.
  8. Install the power steering pump and install the belt.
  9. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
  10. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  11. Refill the engine coolant.
  12. Install the splash shield under the engine.
  13. Connect the negative battery cable.
  14. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

Sep 20, 2010 | 1992 Honda Accord

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

1 Answer

How do you set the timming on a 95 honda accord


1990–95 4-Cylinder Accord and 1992–95 Prelude
  1. .
  2. Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts 86803136.gif
    NOTE: There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.
  3. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
  4. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine. To install:
  5. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
  6. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
  7. Except Prelude VTEC models:
    1. Temporarily install the crank pulley and bolt.
    2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm). NOTE: Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
    3. Tighten the lockbolt installed earlier to lock the timing belt adjuster arm. Remove the crank pulley.
  8. On Prelude VTEC models:
    1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt. NOTE: Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is 1⁄4 fl. oz. (8 ml).
    2. Clamp the mounting flange of the tensioner in a vise using a cloth or blocks of wood to protect it. Insert a flat blade screwdriver into the maintenance hole. Place the stopper (tool number 14540-P13-003) or an equivalent clamp on the tensioner, then turn the screwdriver clockwise to compress the bottom. Be careful not to damage the threads or the gasket contact surface.
    3. Install the maintenance bolt on the tensioner with a new gasket. Tighten to 6 ft. lbs. (8 Nm).
    4. Make sure no oil is leaking from around the maintenance bolt, then install the tensioner on the engine. Make sure the stopper stays in place and tighten the bolts to 16 ft. lbs. (22 Nm).
    5. Remove the stopper. Fig. 11: On VTEC engines, the tensioner must be compressed before installing it on the engine 86803137.gif
      Fig. 12: Remove the stopper after installing the tensioner on the engine 86803138.gif

  9. Make sure all timing marks are positioned correctly (as described earlier).
  10. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
  11. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely. Fig. 13: The balancer shaft must be held in position during timing belt installation 86803139.gif

  12. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
  13. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures. NOTE: Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
  14. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
  15. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
  16. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990–91 Accords, 37 ft. lbs. (50 Nm) on 1992–95 Accords and 43 ft. lbs. (60 Nm) on 1992–95 Preludes.
  17. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following:
    • 1990 Accord: 166 ft. lbs. (230 Nm)
    • 1991–93 Accord: 159 ft. lbs. (220 Nm)
    • 1992–93 Prelude: 159 ft. lbs. (220 Nm)
    • 1994–95 Accord and Prelude: 181 ft. lbs. (245 Nm)
  18. Install the dipstick tube and dipstick.
  19. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
  20. Install the upper belt cover.
  21. Install the side engine mount support bracket if it was removed.
  22. Install the valve cover.
  23. Install the compressor and/or alternator drive belt; adjust the tension.
  24. Route the wiring harness over the valve cover and connect the wiring to the alternator.
  25. Install the power steering pump and install the belt.
  26. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
  27. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  28. Refill the engine coolant.
  29. Install the splash shield under the engine.
  30. Connect the negative battery cable.
  31. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

Jul 18, 2010 | 1995 Honda Accord

1 Answer

I need a belt routing diagram for a 1993 Honda Accord with a/c.


1990-95 4-Cylinder Accord and 1992-95 Prelude

be22676.gif


On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts

120efa3.gif


The balancer shaft must be held in position during timing belt installation

0370564.gif


Timing belt and components used on the Accord V-6

I hope help you with this. Good luck (remember rated this help).




Aug 25, 2009 | 1993 Honda Accord

1 Answer

96 quest.. possible timimg, stopped running at 30mph


check possible broken timing belt by....
removing the distributer cap , and having someone try to start the car .
While it's trying to start , the rotor should be moving... if it's not
timing belt is broken
It's a big job for someone without great skill and a great selection of car tools

Apr 21, 2009 | 1996 Nissan Quest

2 Answers

Timing belt is hard to find


you should be able to call the honda dealer and give them the VIN# to the car and they should be able to pull it up for you.

Oct 12, 2008 | 1993 Honda Prelude

1 Answer

Belt removal or change


i'm not 100 percent possitive but i assume you will have to loosen the tensioner to serpetine belt and it should have a adjustment and just loosen the adjustment. if thats the case you can jump the power steering belt off and back on by prying it with a screw driver and rotating the crankshaft pully

Sep 11, 2008 | 1989 Honda Prelude

Not finding what you are looking for?
1995 Honda Prelude Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...