Question about 1998 Toyota Camry

1 Answer

Ball joints goin out on a 89 chevy s10 blazer

Ball joints going out to much on a 89 chevy s10 blazer how

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 79 Answers

The ball joints are going to be hard to due if you due not have an arbor press in your garage. They are not the kind that you can replace by yourself unforuantely without a press to press them back into the control arm. If you know a good cheap mechanic this would be a good route becuase a shop is going to charge you an arm and a leg to press these ball joints back in for you.

Posted on May 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 89 S10 Blazer. Can I replace the front wheel spindle with one from a 94 Jimmy blazer


If it is a 4x2, yes. If it is a 4x4, maybe. if same engine and tranny in both they will interchange on a good day. If not the same engine and tranny, 4x4 will probably not swap.

Jan 12, 2015 | 1989 Chevrolet S-10 Blazer

2 Answers

My abs light want go out on 1998 chevy s10 blazer it came on after i change my wheel bearing and ball joints


Did you recheck to see if you plugged the speed sensors back in. The speed sensors are built into the wheel bearings on the 4wd models. If you did plug them back in, then one of you new sensors might be bad.

Nov 04, 2010 | 1998 Chevrolet Blazer

3 Answers

How do you remove ball joints from lower control arm on a 1996 blazer s10 4x4(driver/front) .i went to salvage yard and removed but had to buy both arms,nuckle and tie rod. could not separate


By the time you drive the ball joints out of the control arms,they will not be worth driving back in and using,these parts need to be new,the used ones are worn also.

May 23, 2010 | 1996 Chevrolet Blazer

2 Answers

89 s10 has a high idle


Adjust the idle though the throttle body at the top

Apr 16, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

89-98 chevy blazer


It's not worth doing all that conversion, buy the time you spend the time and money to convert the 89 4.3 to work on the 98 blazer, it would be cheaper to install a 98 vortec rebuild. The 89 4.3 have a TBI fuel injection system and the ecm on the 98 will not work and the bad news is that the ecm on the 98 also controls the transmission shift points and the 89 will not, so even if you swap the ecm to have the 89 4.3 engine work. the transmission will not shift. Sorry for the bad news but it would be cheaper to replace the 98 engine with the years of 1996 to 2001. Good luck and hope this helps. 

Jul 21, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

89 chevy S10 turns over won/t start but floods while turning over


If it has a carberater.The flots are probley sticking

Jul 19, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Are 1994 s10 upper and lower ball joints pressed in


the upper ball joints are rivited or bolted if yhey have been replaced before
the lower ball joints on a 2WD are pressed in
the lower ball joints on a 4X4 are rivited or bolted

Jun 04, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Repalce ball joints 01' Chevy Blazer 4WD


you should just be able to loosen the half shaft and be ok that way

Mar 09, 2009 | 2001 Chevrolet Blazer

2 Answers

Location of oil filter on 89 s10 chevy blazer


look at the drivers side rear of the engine next to trans

Jan 15, 2009 | 1989 Chevrolet S-10 Blazer

2 Answers

89 s10 blazer help


have someone check the starter/solenoid

Jul 27, 2008 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
1998 Toyota Camry Logo

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...