Question about 2000 Nissan Quest

1 Answer

Airbag deployed how does the horn button come off the steering wheel of a 2002 nissan quest?

Posted by on

  • Roberta Smith
    Roberta Smith May 11, 2010

    at the rear of the steering wheel there should be some screws you can remove to remove the horn assembly

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers

SECTION 501-20B: Occupant Restraints — Passive — Supplemental Air Bag System 2000 Villager Workshop Manual REMOVAL AND INSTALLATION Module —Driver Air Bag Removal
airbag deployed - syv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The backup power supply energy must be depleted before any air bag component service is performed. To deplete the backup power supply energy, disconnect the battery ground cable and wait three minutes.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. If the vehicle was in a frontal collision and the air bag did not deploy, the air bag may not have been needed. Complete a diagnosis of the air bag system before installing a new driver side air bag module (043B13). Refer to Diagnosis and Testing in this section.

  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Remove the two driver air bag module retaining bolt access covers (one shown).
  1. Remove the steering wheel bottom cover to access the driver air bag module electrical connector.
  1. Disconnect the driver air bag module electrical connector.
  1. CAUTION: After removing, discard the driver side air bag module bolts and install new driver air bag module bolts during installation.
    Remove the two driver air bag module retaining bolts (one shown) and discard.
  1. Remove the driver air bag module.
    1. Separate the driver air bag module from the steering wheel and disconnect the horn pad switch.
    1. Remove the driver air bag module.

Posted on Apr 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air bag light on no horn 2002 suzuki xl7


Most vehicles have a "clock spring" behind the horn button area on the steering wheel. The clock spring has nothing to do with clocks and inst really a spring. It's a flat coil of wiring that is would around in a circle and connected to a stationary item in the middle of the steering column. The outer end of the coil is allowed to move around (coil and uncoil) as the steering wheel is turned. The clock spring typically supplies power to the horn and to the airbag. This is a relatively simple fix, but unless you have mechanical experience, this is a repair I would leave to a mechanic. Pulling the steering wheel and the airbag can possibly lead to airbag deployment and injure or kill you.

Jul 18, 2011 | Suzuki XL7 Cars & Trucks

1 Answer

How do i replace the cruise control on/off switch on my 1999 alero


TO REMOVE CRUISE CONTROL SWITCH. FIRST TURN OFF RADIO TO KEEP FROM LOSING CODE. DISARM AIRBAG IN THE STEERING WHEEL BY REMOVING NEGATIVE BATTERY CABLE WAIT 20 MINUTES FOR AIRBAG TO DISCHARGE BEFORE REMOVING AIRBAG AND HORN PAD IN STEERING WHEEL.ONCE AIRBAG IN STEERING WHEEL OUT.YOU CAN REMOVE THE CRUISE CONTROL SWITCH.BECAREFUL REMOVING AIRBAG IN STEERING WHEEL CARRY IT AWAY FROM BODY WITH AIRBAG HORN PAD POINTING UP.IF YOU DROP IT.DONT PUT IN BACK IN STEERING COULD DEPLOY ON INSTALLATION.

Nov 14, 2010 | 1999 Oldsmobile Alero

1 Answer

Horn wont work


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Sep 24, 2010 | 2002 Chevrolet Malibu

1 Answer

Horn does not work on 97 tercel, benche checked horn ok, took of cover on relay and manually touched contacts together and horn works. Problem appears to be either relay, button or wires. Can the horn...


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

May 28, 2010 | 1997 Toyota Tercel

2 Answers

Why does my horn not work when i try and use it? what could the problem be


Either your horn fuse is blow, the horn itself is shot or the steering wheel switch is bad. It can only be one of those three things.

May 07, 2010 | 2002 Chevrolet Cavalier Coupe

1 Answer

2002 explorer horn inop


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to disarm the airbag system can result in an unexpected Airbag deployment and possible serious personnel injury disconnect the battery 30 minutes prior to start of work.

Mar 29, 2010 | 2002 Ford Explorer

2 Answers

Horn wont honk. Fuse is good and horn honks when hooked up tp 12 volt source. Is there a relay?


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.

Aug 04, 2009 | 2004 Chevrolet Aveo

1 Answer

How to remove the cover off the steering on a 2002


Does your vehicle have an airbag in it? (SEE WARNING BELOW)
If so, you have to let the vehicle sit (no key in ignition!) for AT LEAST 30 minutes to deactivate airbag. Remove the screws from the back of the steering wheel to remove the airbag unit, (once airbag is removed, you should be able to see a little spring and a wire attached to the spring that is a push in and turn setup. That is attached to your horn button and if that is where the short is, fine. If not, you will have to proceed with taking the steering wheel off.) Make sure you make that vehicle sit for as long as possible before removing the airbag. Otherwise, it WILL deploy in your face and set you into the back seat at the very least!!!!!
To be safe, disconnect battery before even attempting to do anything with the steering wheel.

Jul 03, 2009 | 1996 Chevrolet Blazer

2 Answers

Cruise and horn doesnt work 2002 dodge grand caravan


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.

Jun 19, 2009 | 2002 Dodge Grand Caravan

2 Answers

97 Nissan Quest - steering wheel buttons don't work


probably the clock spring uner the steering wheel. It transfers voltage from the steering column to the steering wheel.

Section 11-04: Steering Column 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Sliding Contact, Air Bag Removal
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE BACKUP POWER SUPPLY ENERGY MUST BE DEPLETED BEFORE ANY AIR BAG COMPONENT SERVICE IS PERFORMED. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE (14301) AND WAIT TEN MINUTES.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Match mark and tape in place the inner and outer elements of the air bag sliding contact.
  1. Remove the two steering column shroud screws and the lower steering column shroud (3530).
  1. Loosen the shifter boot and position the upper steering column shroud out of the way.




  1. Remove the three air bag sliding contact screws.




    230e052.gif





  1. Disconnect the two lower air bag sliding contact electrical connectors.
  1. Remove the air bag sliding contact from the vehicle.

Apr 27, 2009 | 1997 Nissan Quest

Not finding what you are looking for?
2000 Nissan Quest Logo

Related Topics:

655 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...