Question about 2006 Nissan Titan

1 Answer

''my nissan titan ac fan stays on high and will not switch to slower speeds''

Posted by on

  • troy621 Apr 16, 2009

    where is the resister pack located

  • Tim Smathers
    Tim Smathers May 11, 2010

    does it slow down if your turn off the ac just blow cold or warm out

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 170 Answers

Replace the resister pack.

Posted on Apr 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Nissan Titan heater/ac fan blows on high we replaced the VBC it did not fix it, now what?


What is VBC? Ah, probably Variable Blower Control? my guess you got wires crossed, or a short around the control or even direct short to hot (12vdc) wire. Double check your work, wire connections. Instructions? with the new? double check.

Feb 27, 2015 | 2011 Nissan Titan Crew

1 Answer

Nissan 2006 blower switch


Fan speed is controlled by a rheostat near the blower motor there will be a connection with three or four wires.

Sep 10, 2014 | 2006 Nissan Titan

1 Answer

On a 2007 lincoln navigator the a/c fan motor will not shut off. the fan adjustment bars are showing slower but still the fan is on high


The fan speed reostat is broken or the switch itself is bad. Try replacing the switch first because the motor speed reostat is part of the motor itself. $$$

Aug 30, 2014 | 2007 Lincoln Navigator Luxury

1 Answer

2009 Nissan Quest My fan works on high all the


The resistor limits power to the blower to make for the slower speeds. It could be a sticking fan relay or the controller.

Aug 12, 2013 | 2002 Nissan Sentra

1 Answer

Ac will not blow out vents


Hi, each fan or blower have switch to work on high and low blowing air. Check your blower switch first.

Jul 19, 2013 | Nissan Titan Cars & Trucks

2 Answers

The AC button light blinks on and off. AC won't


When the light is blinking that means there is a code in the system you will have to take it to a shop and have the codes read. Sometimes "Jiffy Lube" or "Rapid Oil Change" can read the code for but they won't fix it. If the blower motor only runs on high, the blower motor resistor is bad. When you put the fan switch on high it puts full voltage to the fan motor (blower motor) when the fan switch is in any other position, the voltage is reduced by the resistor causing the motor to run at slower speeds. The two problems are probably a result of the resistor.

Dec 14, 2009 | 2003 Chevrolet Malibu

1 Answer

AC is stuck on high on my nissan titan 2006. I have heard it may be the resistor or the control panel


The blower resister is near the blower motor,mounted on the outside of the blower box,but actually goes inside the blower box.It~s function actually is to give the blower motor lower speeds.If it is only working on high,then this is the problem.If it works on high when you select a lower speed,then there is a high blower motor relay that is stuck in the closed position .Replace the relay.

Sep 09, 2009 | 2006 Nissan Titan

1 Answer

Ac controls quit working blower fan is running on high all thetime. compressor is not working.


fan elays are under hood in black box by battery. 3 of them. 2 for high speed, 1 for low speed. Default is high speed when there is a probem.

Suspect maybe they shorted something out when fixing dent. Did they do any welding on the van? Connecting the cables to the body can sometimes send voltage where it's not wanted.

Nov 06, 2008 | 2000 Nissan Quest

Not finding what you are looking for?
2006 Nissan Titan Logo

Related Topics:

1,989 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...