Question about 1983 Ford Mustang Hatchback

1 Answer

I have an 83 stang i have stater problems can somone help i am tring to remove it it is a 3.8l thankz a mill

Posted by on

  • 2 more comments 
  • Anth Apr 16, 2009

    ok i diconnectected my battey and i tool the wireing off the cylinoide i cant get the wiring off the starter but i managed to get out the 2 bolts holding it in. after that i tried to move the started and it will not budge. is there any chance that there could be any other bolt or plates holding it in??? thankz

  • Anth Apr 16, 2009

    thankz i will check it out today and get back to you

  • Anth Apr 16, 2009

    i just called ford and found out that is is only 2 blot in the starter and a plate on the bolting end if anyone has seen this could they possibly tell me how to to get it out

    thankz

  • Anth Apr 16, 2009

    k thankz

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 226 Answers

You have to first disconnect the battery, then raise the vehicle. Then you have to disconnect the wires from the starter /soinoid as well as pull the plastic plug straight back on the soinoid, since there is a connection inside it which you don't want to damage. Then you remove the starter bolts & remove it. I am assuming that you know what the starter looks like. Not too much work, but you need to put the wires back exactly where they were in the first place. Rick

Posted on Apr 16, 2009

Testimonial: "it did help but is was only 2 bolts but i did end up getting it out and replacing it thanks chev49"

  • Rick Reichlein Apr 16, 2009

    I think that there are 3 bolts holding it in. i by the solonid, (11 o clock position) and two more one about 8 o clock position and the other abt 4 o clock position., Check that. I think that I have the right motor. Rick

  • Rick Reichlein Apr 16, 2009

    I will have to look it up. Rick

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Facebook login


You'll need to contact facebook directly.

Jan 21, 2014 | 2003 GMC Sierra

1 Answer

1987 cutlass RWD 3,8L spark plug wire firing order?


1-6-5-4-3-2- vin.A 2bbl1987 Oldsmobile Cutlass
3.8 liter V-6 VIN "A" 2-bbl41894086.gif

Sep 03, 2012 | 1987 Oldsmobile Cutlass Supreme

1 Answer

New stater, stater still makes clicking sound


First you should check to make sure the engine is not locked up by turning it over manually. If you can turn the engine manually, then check your battery terminal ends to make sure you have good, clean and tight connections. Typically, a faulty electrical connection is the main culprit that will cause your situation. If you still suspect a faulty connection, try having someone turn the ignition key while you wiggle the battery cables to see if it will try to start. This should help you narrow down the problem area.

Sep 02, 2012 | 2003 Mitsubishi Galant

2 Answers

Electric problem/get off panel light


Stater more?? What does that mean?

Apr 27, 2012 | 1990 GMC Sierra

1 Answer

My '03 Stang GT won't start. I turn the key and nothing. It has 30g miles, and a friend said it is probably a fuse, not the battery. A jump start did not help. Any ideas?


I believe those vehicles have a spade terminal on the starter it has a plastic square covering on it grab it and wiggle it and pull and push it than try to start those connectors get corroded and dirty!

Nov 30, 2011 | 2003 Ford Mustang

2 Answers

Hi. Can i use the gearbox from a 2001 Dodge Grand Caravan 3,8L, in my 96 Dodge Grand Caravan 3,8 L


sorry have to ask. which gearbox? steering,transmission? if its the trans yes. if its the steering no.

Jan 20, 2011 | Dodge Grand Caravan Cars & Trucks

2 Answers

How to install a starter on a 1991 chevrolette silverado


2wd or 4wd, 1500, 2500, 3500, 4.3, 5.0, 5.7, 6.2, 7.4 ? need information along with email address to send directions to replace starter

Feb 07, 2010 | 1991 Chevrolet Silverado 2500

1 Answer

You drive this car 15 to 20 miles fine then it staters acting up it doesn't want to run over 20 miles per hour with out tring to cut off


I have done this work for 25 years and who ever he is that said the ECM may be bad is most likely incorrect, the ECM or computer is the last part that fails, the failure rate is about 2%, need to know the codes you have to give further assistance to you, thanks

Sep 03, 2009 | Lexus ES 300 Cars & Trucks

4 Answers

83 mustang gt


In a 83 MUSTANG GT the correct answer is BOTH. As a 5.0L and a TURBO CHARGED 4 cyinder were offered.


1983 Mustang GT
  • Engine:
    • 5.0L horsepower increased to 175 HP when 4V carb replaced 2V carb from 1982 (Holley 4180C series).
    • Exhaust system was revised (less restrictive).
    • 4-speed SROD was only transmission available until early December 1982. In December, new 5-speed T5 became standard GT transmission (4-speed remained on option list).
    • Block and crank were revised to accomodate a 1-piece rear main seal in December 1982.
    • The new "Turbo GT" with a turbo charged 4 cylinder engine was available beginning late in the model year - 145 HP and featured the same suspension and other features of the V8 Mustang GT.

Jun 02, 2009 | 1983 Ford Mustang Hatchback

1 Answer

Toyota starter problrm


NEED TO REPLACE STARTER.

Mar 03, 2009 | 1996 Toyota T100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...