Question about 1988 Ford Crown Victoria

1 Answer

No heat from heater

1988 Ford Crown Vic. Both heater hoses are hot, but no heat at all from heater. Temp control, seems to work a cable o.k. under the dash. Does the blend door, work by a cable, or vacuum? This is a LX car. terryh@santel.net

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Make sure you have vacume too the control diapram

Posted on Apr 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace heater relay on a 2005 ford crown vic


Do you have a manual or electronic automatic temp. control ? What's not working , blower not blowing air ? most of the time the blower motor resistor is at fault.

Oct 20, 2014 | 2005 Ford Crown Victoria

1 Answer

Does a 2009 crown vic have a heater control valve if so where is it located


yes its a blender door accuater some are vacuum controlled and some electric, and ther is a heater control valve under hood on passengers side tward fire wall ,its in the heater hose line.

Oct 17, 2014 | Cars & Trucks

1 Answer

98 E350 7.3 diesel no heat from heater.


There should be three. Temp control, fresh air, and vent direction.

Jan 27, 2014 | Ford E-150 Cars & Trucks

1 Answer

The heating in my 2001 Crown Vic is delayed for 15-20 mins. It has been aprox. -10 to low teens lately. Do you know the issue?


With the outside temp being so low you can expect the heating in the vehicle to take longer to heat up and possibly not be as hot as if the temp was somewhat higher.

Jan 05, 2011 | 2001 Ford Crown Victoria

1 Answer

When i change the control from hot to cold it stays hot. Then i put a new controler box in and i get the same thing? The car is a 2006 crown vic p71.


Check the operation of the temperature control actuator. It is located on the top of the heater case. If it doesn't move when adjusting the temp. the actuator is probably bad. It is no an easy task to replace. The case hase to be lowered to get to it.

Mar 11, 2010 | 2006 Ford Crown Victoria

1 Answer

The climet control heating systom moter in my 04/Crown Vic runs at full spead at all times all I can do is turn it off or on can you help "Thanks HARDLUCK"


If you have eatc and the blower stays on with the system off. It is your blower speed controller.It's located under the hood in the evap. case under the heater hoses. Follow the wiring from over the hoses.

Mar 10, 2010 | 2004 Ford Crown Victoria

1 Answer

Cant loc the idle air control vavlve located on a 1988 crown vic


attached to the throttle body,looks like an electric motor bolted to a square piece with the corners notched out,with 2 wire connector on the end.

Feb 19, 2010 | 1988 Ford Crown Victoria

2 Answers

The heater blower motor on my 2001 ford crown vic won't work. i checked the fuse and took the motor out and had it checked and it's OK.


look for relay or resistor heater box under hood passenger side follow heater hoses 2 two heater box coming out of fire wall

Jan 25, 2010 | 2001 Ford Crown Victoria

2 Answers

96 ford crown vic over heating


it seems you have to seperate issues here. fiirst let's start withtthe over heating. you stated that you have replaced the pump,thermosta,fan,clutch,all the hoses, and core. now my question to you is did you route the belt so it's circulating like it should? is it steaming out from under the hood? to be quite honest the vehicle should not even be close to overheating after driving only 3 miles. there is a possibilty that you have a bad sending unit for the temp if it is not steaming out from under the hood. your upper radiator hose is hot this tells you that the thermostat is operating as it should. the fan should be turning clock wise as you are looking at it from the front of the vehicle.when you fill the system with coolant make sure that you have the heater on high and to the hot setting. check to make open sure you have plenty of coolant and that the radiator is free of dirt and bugs.. now as far as not having anyheat in the vehicle check the fuse for your climate control. look under the dash and make sure you hooked all the cables for your fresh air door and blend door. when you changed the core did you connect the hoses in the right place?after you have checked all the hoses and the coolant is as full as can be and the heat is turned on to max ,keep the radiator cap off and start the vehicle wait for it to get hot check the upper radiator hose to see when the thermo stat opens you should see that the coolant should go down in the radaitor. do these things and check back with me on the results...please rate this help...thanks

Sep 22, 2008 | 1996 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...