Question about Mercedes-Benz 190-Class

1 Answer

Replaced dist. and don`t know ignition timing specs.also don`t know how to determine what motor i have. no info under hood, thank you(82 mercedes 380sl)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 408 Answers

Hello, in your registration paper they write engine number or try to look your engine number, in upper engine block,start with 116.9_ _ ,you can use this number to all your inquires,pls. post your engine,so i could post your inquires,ty

Posted on Apr 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The ignition timing specs and procedure for my 96 geo metro


Best Manuals


For the best solution of your problem visit this site.

Sep 05, 2016 | 1996 Geo Metro

1 Answer

Have 82 f100 with 3.8 motor when I let out clutch it bogs down ?


truck got tune up recently? good spark from each plug (ignition coil, distributor cap & rotor if equipped, spark plug wires), good fuel delivery, idle rpm & ignition timing set to specs? transmission turns freely?

Oct 07, 2015 | Cars & Trucks

1 Answer

Set up timing on a 1989 toyota corolla 1.6cc twincam


look up under your hood there should be the specs.i think its 10 or 12 degree,install your timing light cables to battery pos.and neg. and the clamp to #one ign.wire loosen the bolt with 12mm ranch and turn dist. to the specs.

Aug 05, 2012 | Toyota Corolla Cars & Trucks

2 Answers

When I put it in reverse it goes dead. the idle is too low, so I am using my foot for brake and idle when I come to stops. What the heck? Sensors? Air Idle? Let me know whatcha think a chic...


Chic Mechanic, I like that. Take and smear the grease from your fingers on your face like war paint and let out a Zenna yell.

The IAC could have some carbon build up on it, or not working properly. Unplug it and see if the motor just dies. You can also remove it and clean any carbon off. Also carbon can build up on the EGR and keep it open a little bit. And check your ignition timing. If you have an under hood label it should give instuctions and specs. It should tell you there is a tan (or tan with black stripe) single wire that needs to be unplugged. I don't recall the exact location but it will be in the large computer harness (usually sticking out of the loom) under the hood where it goes into the truck or under the dash near the ECM.

Sep 21, 2011 | 1991 Chevrolet C1500

1 Answer

1992 Mercedes 190E: there is a constantly-runnung air circulation motor somewwhere under the dash; it is wextremely noisy on a cold morning, and I just want to give the motor bearing a shot of lubricant....


think again its under the hood behind the fire wall it should be 6 hex head screw to remove the black panel this is a time consuming job so i would replace the part instead of waisting your time with lube if you want i have the part you need let me know

Jan 05, 2011 | 1993 Mercedes-Benz 190

1 Answer

My Heater is not working in my 2003 Honda Element


First check and confirm the fuses related to heater in your car.Fuse #12 (40A) in the under-hood box powers the blower motor. Fuse #14 (10A) in the under-dash box powers the blower motor relay as well as the A/C compressor clutch relay, A/C condenser fan relay, power mirrors, radiator fan relay, recirc. control motor, and rear defogger relay.If the fuses are blown then replace the fuse and check.But if the problem is still there then Its a heater relay problem,.The blower motor relay is in the under-hood fuse box. It's larger than the rest, on the back side, labeled RY6.Remove the relay. With the ignition off, use a 12V tester to locate the constant-power socket, which powers the motor via the relay. Then with the ignition on, locate the switched-power socket, which powers the relay. Verify that neither of the remaining two sockets is powered, then with the ignition off use a continuity light to determine which is ground. The last socket goes to the motor. (If the continuity tester lights on both, it's probably because the motor has fairly high resistance, and you'll need an ohmmeter to determine which socket is ground and which goes to the motor.)With a fused 12V power source, power the relay's coil contacts and check the other two contacts for continuity. If the relay doesn't work, replace. But if the relay is also checked ok.then in that case the blower motor is faulty causing this problem.Make sure it has power at the connector and that the connector is properly seated. If the power and ground connections are fine, then the motor is bad. ----------- This troubleshooting procedure will help you to confirm the possible problem.Thanks.Helpmech.

Nov 12, 2010 | 2003 Honda Element

1 Answer

Timing specs


Should be under the hood,on a lable! You may nave to bypass the computer,and i,m not sure how so the specs alone are ok to know,but the bypass to check or set the ignition timing is a must! It may tell under the hood on a lable some where check really good!

Sep 06, 2010 | 1998 Ford Mustang

1 Answer

What do you set the timing at on a 69 chevy 350


diaconnect the vacuum advance, and loosen the distributor hold down bolt just enought so you can turn the distributor, at idle turn dist, to advance mark on the harmonic damper to spec, either found on a sticker under the hood of from manual, need a timing light, tighten dist bolt ,

May 26, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

Hello, i have the 82 mer. 380sl with the 116.962 motor and unsure how to set timing after replacing the dist. thanks for all your help, jeff


ok,hoping before you remove your dist. ,cylinder number one in top dead center,install dist.align rotor to mark in dist. housing,ignition timing with out vacuum 25 degrees,using timing light , hoping it help you,ty

Apr 16, 2009 | 1985 Mercedes-Benz 300

2 Answers

Set timming


You will need a timing light for Hi energy ignition as well as standard socket set or wrenches. 1. get the engine up to operating temp. 2 shut off engine connect the timing light to the number one[1] spark plug wire at the spark plug end connect battery connectors. 3 start engine and note location of pointer on the mark tab on the timing cover. 4 shut off engine loosen the hold down clamp on the distributor turn the bolt no more than one full turn[snug is better than loose here] then note the position of the dist. cap. Move the dist. to make sure it moves freely replace back to the starting position and remove and plug the vaccum line to the dist. 5 start engine and set timing to the desired spec. 6 shut off engine tighten dist. clamp bolt 7 start engine check timing one more time to see if still there at desired setting. 8 shut off engine dis-connect all tools and light

Apr 02, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...