Question about 1992 Subaru Legacy

1 Answer

1992 subaru legancy no spark from cylinder 3 and 4 pls hellep thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Look at the igniter. you should have 2 wires that have a 5volt square wave form. These are the signals coming from the computer. You should also have 2 wires that have a ignition primary wave form. These are the signals that the igniter sends to the 2 coil packs. If they all looked ok. check the igniton coils. if all looks good then look at the crank and cam shaft signals before the computer. If they look ok check for good power and grounds to the computer. If all looks good have the computer repaired.
Sounds pretty easy doesn't it!!!????
I hope that helps

Posted on May 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change clutch adjustment arm on 1992 Subaru legacy


If you mean the release arm that goes into the transmission, removal of the transmission is required.

If you mean the rod from the slave cylinder to the release arm, undo the two bolts that secure the slave cylinder, and the rod will come out.

Feb 21, 2015 | 1992 Subaru Legacy

2 Answers

P0303 p0304


You'll have to get someone to check the spark and injector on cylinders 3 and 4.
Code 303 is for loss of power on cylinder 3 and code 304 is the same for cylinder 4. The most common causes are lack of spark or fuel.
Once the problems are fixed the codes will need to be erased with a scanner or code reader.

Jun 11, 2013 | Subaru Cars & Trucks

1 Answer

Donde se encuentra el fusible para el radio, del subaru legancy outback 2001.


were find fusible of the stereo or radio isuzo rodeo 2001

Feb 12, 2013 | 1997 Subaru Outback

1 Answer

Where is the #1 cylinder on the subaru legacy 1992


Cylinders are 1-3 on the LEFT side front to back and 2-4 are on the RIGHT side standing at the FRONT of the engine.

Jan 01, 2011 | 1992 Subaru Legacy

3 Answers

I need a spark plug wire diagram for a 1992 Toyota Camry 4 cylinder


1992 Toyota Camry Sedan
3.0 liter DOHC V-6 (3VZ-FE)

Cylinder # Front, passenger to drivers side 2-4-6
Cylinder # Back, passenger to drivers side 1-3-5

Distributor 12 O'clock post # 6 cylinder
10 O'clock post #1 cylinder
8 O'clock post #2 cylinder
6 O'clock post #3 cylinder
4 O'clock post #4 cylinder
2 O'clock post #5 cylinder

Good luck and hope this helps.

Jan 12, 2010 | 1992 Toyota Camry V6

1 Answer

My legancy 2000 automatic gear shifts at ruv 3400 rpm .is it normal?


depends on gas pedal position,the lighter you are accelerating the earlier the trans should shift,if it always hangs on in gear get it looked at...as it can shift at redline (5000-6000 rpm,if you hold the gas peadl down fully).

Oct 28, 2009 | 2000 Subaru Legacy

1 Answer

Car jerking/bucking in cold weather


fuel air or spark.. dead miss one one or 2wo cylinders indicated ..check plugs /wires / injectors timing and vacuum leaks ...good luck

Jan 13, 2009 | 1992 Subaru Loyale

1 Answer

1992 subaru


The best way to check for spark is to remove a sparkplug wire from one of the sparkplugs on you engine and then take one of the spark plugs that you replaced and connect it to that plug wire. Make sure the plug is touching bare metal and have someone crank your engine. You should see a spark at the end of the plug. As far as a stuck injector you need to see if your getting spark first. Let me know what you find.

Jan 02, 2009 | 1992 Subaru Legacy

1 Answer

1992 Isuzu Rodeo Distributor wires


Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Jul 05, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
1992 Subaru Legacy Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...