Question about 2006 Datsun Stanza

Open Question

JET SIZES DATSUN STANZA 1982

Hi! i need main and secondary jet sizes for nikki carb on datsun stanza 1800 (L18). the ones below fuel window with the #12 bolts that secure them. also the correct way to set idle mixture and idle speed. thanks imo

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: Datsun stanza 1980 tappets (lifters)

This car has hydraulic lifters( tappets} therefore should not adjustment, you probably have a bad or weak lifter. But, in any case you have to remove the valve covers to make the adjustment. You will see the adjustable bolt on the rocker arm. rotate the engine until the valve is all the way to the top, [no tension on the valve spring] then place a feeler Gage in between the rocker arm and the valve stem, adjust the rocker arm until the feeler Gage is snug but not tight. Do this with each valve. Check the book for the correct Gage to use but I think it is a .018.

Posted on May 15, 2008

mmptruck
  • 124 Answers

SOURCE: datsun stanza 1800

Check ignition coil, they are known to short circuit after a wash.
Try starting engine at night or in the dark and look around coil and leads for hi voltage sparks.

Posted on Aug 08, 2008

  • 599 Answers

SOURCE: Contact Point Gap 1981 Datsun Stanza

cool old car :)...set points at .019 in. new ...and .016 if using used

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1982 Datsun pickup that sputters and stalls when I go over 35 mph or up a hill help please


This is a timing issue.. The age of the vehicle has also put a lot of miles on the timing for the ignition and possibly the physical timing. You are going to have to get new distributor parts

Mar 09, 2016 | Datsun Cars & Trucks

1 Answer

What's the valve clearance on a 1982 Datsun 720


Try the chiltons manual at your local library

Apr 01, 2012 | 2005 Datsun 720

1 Answer

Clutch slipping


if no adjustment left either worn or possibly rear engine seal leaking oil onto it

Sep 24, 2010 | 2006 Datsun Stanza

1 Answer

Contact Point Gap 1981 Datsun Stanza


cool old car :)...set points at .019 in. new ...and .016 if using used

Nov 10, 2008 | Datsun Stanza Cars & Trucks

1 Answer

Datsun stanza idle speed


Water vapor in your distributor cap will cause those conditions, especially after engine washing. Remove and dry the distributor cap and it should run fine aftrewards.

Aug 08, 2008 | 1983 Nissan Stanza

2 Answers

Low idle speed


if you washed the engine bay theres a chance you may have got water into the spark plugs or on the distrubutor, remove dizzy cap and remove water from the underside, sum crc products work well at this. usually after the engine gets hot it will evaporate the water away, I hope you don't have an exposed air filter, this could also be wet causing starvation. sum more info would be helpful

Aug 08, 2008 | 2006 Datsun Stanza

1 Answer

Datsun stanza 1800


Check ignition coil, they are known to short circuit after a wash.
Try starting engine at night or in the dark and look around coil and leads for hi voltage sparks.

Aug 08, 2008 | Datsun Stanza Cars & Trucks

1 Answer

Datsun stanza 1980 tappets (lifters)


This car has hydraulic lifters( tappets} therefore should not adjustment, you probably have a bad or weak lifter. But, in any case you have to remove the valve covers to make the adjustment. You will see the adjustable bolt on the rocker arm. rotate the engine until the valve is all the way to the top, [no tension on the valve spring] then place a feeler Gage in between the rocker arm and the valve stem, adjust the rocker arm until the feeler Gage is snug but not tight. Do this with each valve. Check the book for the correct Gage to use but I think it is a .018.

May 15, 2008 | 2006 Datsun Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Datsun Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8190 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Datsun Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...